[washman3]

Re: Nordmende tumble dryer.

Button is broken for sure.!

[washman3]

Re: Nordmende tumble dryer.

Unfortunately not. i’ll place it under a large magnifying glass tomorrow and try to find the imprint of one.
If I could find the White Knight corresponding model number it would be a big help.

[washman3]

Re: Nordmende tumble dryer.

Thanks Dave,
Need a belt and an ON/OFF switch.

[washman3]

Re: Siemens IQ300 E23

Thanks again Martin. I was suspicious of the doorlock, bit cheepish looking on this model, just clipped in place,no screws. However it is locking but the module is refusing to unlock it as it thinks there is water in the drum. I blew air through the small hose to the pressure chamber, no blockage, but as you say, maybe the pressure switch is acting up.

[washman3]

Re: Siemens IQ300 E23

Thanks for reply. My manual said it was a blocked pump of pump relay problem.
I put 5 litres of clean water in the drum, unscrewed the drain plug and it all flowed out. So no obstruction. Removed the large black drain hose, sump is clean,as is the grey drainpipe. The small hose from the sump to the pressure switch is also free.
No other Anti-Flood device that I can see. Heater element is also ok.
After these checks still have E23.

[washman3]

Re: Beko DW600 integrated dishwasher.

Thanks. That may be the best way to go. Did a wash today without tripping the rcd. Fault is intermittent.

[washman3]

Re: Beko DW600 integrated dishwasher.

Regular moulded 13amp plug that was factory fitted to the appliance. Plugged into the same socket as the old hotpoint.

[washman3]

Re: Transporting Fridge need advice

Many thanks folks. your advice is much appreciated..

[washman3]

Re: Hotpoint SDW60

I have contacted the administrator regarding this. thanks

[washman3]

Re: Hotpoint WMA42N door light flashing…

Many thanks for the advice. will try the repair,if its knackered i will be giving EMW a call.!!
Shame that the PCB is the “fuse” on these machines.! 😕

[washman3]

Re: Hotpoint WMA42N door light flashing…

Had actually checked the PCB in the meantime and found a burnt track corresponding with door interlock. i’m actually a dab hand at solder repair. damage is extremely slight. would repairing and fitting a new door interlock be recommended. Though machine is old in years its actually in mint condition and would be a shame to scrap. many thanks for your help.!

P.S. would it be possible to PM you IADIOM re Trade Forums. i have read and understand the terms required.

[washman3]

Re: Indesit 143s (uk)

Thanks. removed paddle out of curiousity. “coin” turned out to be a bra wire which i was just about able to retrieve with a long-nosed pliers. coin removal would definately be impossible through these slots.

[washman3]

Re: Indesit 143s (uk)

bearings and seal replaced without removing the drum from the machine. But definately care to be taken as edges are razor sharp. By the way,whats the best way to remove a paddle in order to take out a coin? think it would be faster than removing the sump hose.
I know some machines have a press-tab on the 3rd hole from the front, is this model similar.?

[washman3]

Re: Indesit 143s (uk)

Thanks. i’ll remove it and have a look anyway.(leather gloves on hand as i’ve been caught before).!!
Let you know how i get on. Cheers..

[washman3]

Re: Zunussi ZWF 1437W

Thanks for useful acvice Scott. done as you suggested and had no problems. Blockage was at the elbow where pipe entered door seal.
No vent pipe near dispenser on this model. Machine working perfectly again.

[Author]

Posts