A1TEC

Forum Replies Created

Viewing 15 posts - 61 through 75 (of 395 total)
  • Author
    Posts
  • in reply to: CK Tools #402394
    A1TEC
    Participant

    Re: CK Tools

    As above, all the usual hand tools and megger insulation tester.

    in reply to: WTA & Conference Chat Thread #402951
    A1TEC
    Participant

    Re: WTA & Conference Chat Thread

    lee8 wrote:

    jamieparrie wrote:
    hello k.im just finding it hard to see wat 70 pound will get me apart from discounts.even if you got us some work offers,unless it was a tender style offer,we wouldnt do it as pay to cheep and they want to much for the low pay.
    in electrical trade we tender for work with housing associations,builders ect and we put forward our best rates and terms then they chose one and sign a duration contract.here,it seems to be the other way around.which is messed up.i had one firm say to me that if a machine gets exchanged then we get 20 pound.even if not our fault.needles to say we said no thatnks but reading this i thought you might have had a different way like tendering so everyone makes there own terms and then competes for work.
    although niceic is a lot of money its a recognised body and they help with certificates ect aswell as provide jobs at charge rates.so to me,i could make the few hundred pound in one job.but with this and only having discount club,i wouldnt get my money back as i wouldnt want the work unless it was tendered or contracted legaly.
    and to the person above me that said me and national appliance care were in cardiff,i just double checked,there in wakefield yorkshire so you are wrong.

    I would suggest that maybe you should invest the £70.00 in some other form of learning and then when you have achieved the required level re look into joining the wta, you may find that it will become a little clearer as to what you’ll get for your money.

    Well said lee8, i was getting dizzy reading the above posts. 😆

    in reply to: Commercial #395497
    A1TEC
    Participant

    Re: Commercial

    I am one of a few who do catering equipment and whitegoods.
    I have never found any forums like ukwg for catering or commercial laundry.

    in reply to: Beko Laundry Tech Info #391446
    A1TEC
    Participant

    Re: Beko Laundry Tech Info

    Dave pm’d you re above.

    in reply to: Gas oven suggestions #392900
    A1TEC
    Participant

    Re: Gas oven suggestions

    lee8 wrote:Baumatic.

    They cook very quickly, most will roast a joint in 10 minutes.
    I think there must be a problem with the oven stat calibration then! :rotfl:

    in reply to: Agora employment #392668
    A1TEC
    Participant

    Re: Agora employment

    I have met and spoke to a few of their engineers and sub contractors in the last 6 months, they have been around for a while and have a wide and varied contract base.
    They guy’s that I spoke to were kept busy and seemed content with their employment.

    in reply to: RAW #386023
    A1TEC
    Participant

    Re: RAW

    Would only pay £20.00 for raw as I do up here, £30.00 is chancing it a bit.

    in reply to: Bendix BIW 105w #381398
    A1TEC
    Participant

    Re: Bendix BIW 105w

    Yes it is not heating after the new heater has been fitted, it will go through the wash but does not heat.

    John

    in reply to: a quiet few days #370897
    A1TEC
    Participant

    Re: a quiet few days

    Only picked up in the last few weeks, been quiet since Xmas.

    in reply to: Unreal prices. #370414
    A1TEC
    Participant

    Re: Unreal prices.

    robinsonrobbo wrote:for built ins ive been using appliancesonline as they are cheaper retail than i can buy trade!

    I have seen their site, like you say some very good prices.
    Just a pity that no one supplies at a good trade price, if they did they would sell loads 💡 there is a idea for any forward thinking seller ❗ 😆

    in reply to: Unreal prices. #370412
    A1TEC
    Participant

    Re: Unreal prices.

    I was wondering who is the best wholesaler out there for machines just now?

    in reply to: Graffters #369078
    A1TEC
    Participant

    Re: Graffters

    Is it the whole group UK wide that is gone?

    in reply to: EEE Safe Certification #357502
    A1TEC
    Participant

    Re: EEE Safe Certification

    Yes sounds like a great idea.

    in reply to: Possible some untested raw whitegoods #350263
    A1TEC
    Participant

    Re: Possible some untested raw whitegoods

    Any news on the raw?

    cheers

    John.

    in reply to: where has all the work gone #351206
    A1TEC
    Participant

    Re: where has all the work gone

    Been slow for the last month, it can only get better. :haier:


    John.

Viewing 15 posts - 61 through 75 (of 395 total)