allan73

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 497 total)
1 2 3 … 32 33 34
  • Author
    Posts
  • January 7, 2015 at 11:23 am in reply to: Whirlpool AWG345/4 85373041550 E14 fault #423302
    allan73
    Participant

    Re: Whirlpool AWG345/4 85373041550 E14 fault

    Could this be a Smeg built Machine ?

    Allan

    November 15, 2014 at 7:30 am in reply to: Bosch WAA28161GB/09 surging motor #421468
    allan73
    Participant

    Re: Bosch WAA28161GB/09 surging motor

    Thanks Dave, I’ve ruled our motor now must be the board.
    I’ve not had problems with motor triacs before on Bosch machines.

    Allan

    October 20, 2014 at 8:45 am in reply to: Beko DRCS68w overheating #420551
    allan73
    Participant

    Re: Beko DRCS68w overheating

    Ok I’ll go back and check again.

    Allan

    October 18, 2014 at 12:04 pm in reply to: Beko DRCS68w overheating #420549
    allan73
    Participant

    Re: Beko DRCS68w overheating

    Yes Seamy heater the heater I fitted had an NTC and a resettable cut out. Cut out is now tripping.
    Allan

    October 18, 2014 at 10:28 am in reply to: Hotpoint WMUD963 PUK Door Seal #419887
    allan73
    Participant

    Re: Hotpoint WMUD963 PUK Door Seal

    ‘Twas packed incorrectly.
    Allan

    October 1, 2014 at 6:54 pm in reply to: Hotpoint WMUD963 PUK Door Seal #419886
    allan73
    Participant

    Re: Hotpoint WMUD963 PUK Door Seal

    I thought that Martin. Could be packaged incorrectly ?

    Allan

    October 1, 2014 at 6:19 pm in reply to: Hotpoint WMUD963 PUK Door Seal #419884
    allan73
    Participant

    Re: Hotpoint WMUD963 PUK Door Seal

    Yes Qualtex are adamant that’s the correct seal but as you can see from photos it’s different.
    I’m wondering if someone has changed the drum for a slightly different one at some point ?
    Allan

    September 27, 2014 at 12:26 pm in reply to: Whirlpool AWOR/R4205 fault code ? #419697
    allan73
    Participant

    Re: Whirlpool AWOR/R4205 fault code ?

    Customer has unplugged and waited for door to open. Machine is now completely dead.
    Allan

    September 9, 2014 at 7:14 pm in reply to: Hoover HNWF washer dryer f12 #418727
    allan73
    Participant

    Re: Hoover HNWF washer dryer f12

    Ok I’ll take a look, thanks
    Allan

    September 9, 2014 at 6:34 pm in reply to: Hoover HNWF washer dryer f12 #418725
    allan73
    Participant

    Re: Hoover HNWF washer dryer f12

    He’s had the facia off to change the selector. I’ll check ribbon cable and board connections..
    Allan

    September 9, 2014 at 6:24 pm in reply to: Neff S44T09N3GB/06 no heat #418982
    allan73
    Participant

    Re: Neff S44T09N3GB/06 no heat

    Thanks Martin, I better check the spray arms.

    Allan

    September 9, 2014 at 6:21 pm in reply to: Hoover HNWF washer dryer f12 #418723
    allan73
    Participant

    Re: Hoover HNWF washer dryer f12

    Had customer take photos of dryer area on this and I can only see stats, no NTC ???

    September 9, 2014 at 6:16 pm in reply to: Neff S44T09N3GB/06 no heat #418980
    allan73
    Participant

    Re: Neff S44T09N3GB/06 no heat

    Could be poor pressure from circ pump then Martin ?

    September 5, 2014 at 8:09 pm in reply to: Hoover HNWF washer dryer f12 #418721
    allan73
    Participant

    Re: Hoover HNWF washer dryer f12

    Will do thanks Martin. The customer states he changed the selector because ” it was doing strange things and going on the wrong setting”
    Allan

    September 5, 2014 at 7:26 pm in reply to: Hoover HNWF washer dryer f12 #418719
    allan73
    Participant

    Re: Hoover HNWF washer dryer f12

    Thanks Bryan
    It heats so I’m guessing it’s the NTC.
    Allan

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 497 total)
1 2 3 … 32 33 34