[Ashby]

Re: Zanussi Dishwasher Mod DES 959

Hi Gegsy, Thanks for your help with that one. I’ll let you know how i get on. Ashby 😆

[Ashby]

Re: TECNIK DISHWASHER TKD-751

Hi Bryan, Thanks for your help. I’ve now orderd the door seals.
Much appreciated.
Ashby

[Ashby]

Re: Zanussi DE6854

Hi Chris, Just had the same problem myself. A blob of solder on the heater relay did the trick.
Ashby

[Ashby]

Re: Zanussi Dishwasher Mod DE 6850

Hi Guys, Thanks for your help. A blob of solder on the heater relay did the trick.Much appreciated.
Ashby.

[Ashby]

Re: Zanussi Dishwasher Mod DE 6850

Hi, Thankyou all for your help. I’ll let you know how i get on.
Many Thanks.
Ashby

[Ashby]

Re: Bosch Dishwasher Enr SGS6312GB/12 FD 7910 740079

Hi, Thankyou both for your advice, i’ll have another look tomorrow.
Much appreciated.
Ashby

[Ashby]

Re: SMEG DISHWASHER MOD DWF66

Hi, Does anyone have a second hand PCB for this machine? I don’t really want to buy one at 108.00 + VAT and it doesn’t cure the problem.
Many thanks.
Ashby

[Ashby]

Re: Bosch Washing Machine Enr. WFL2450UK/12 FD 8202 600 259

Hi Bryan, Yes the motors were out of stock when i phoned. I was told they were expecting them in about 2 weeks. On friday they rang to say they were in. 104.00 plus vat.
Thanks.
Ashby

[Ashby]

Re: Bosch Washing Machine Enr. WFL2450UK/12 FD 8202 600 259

Thankyou all for your help on this one. I’ve just orderd one from Masterpart. 104.00 pounds plus VAT. Washvac quoted 150.00 plus VAT.
Many Thanks.
Ashby

[Ashby]

Re: Bosch Washing Machine Enr. WFL2450UK/12 FD 8202 600 259

Thanks Chris. I’ll give them a ring in the morning.
Much appreciated.
Ashby

[Ashby]

Re: SMEG DISHWASHER MOD DWF66

Hi, Thankyou both for your suggestions. Iwent back today and tryed what you suggested, without success. It’s still doing the same thing. However, when i tryed it on a soak program (P1) it worked perfectly. This program i notice doesn’t take detergent or requires heat. i removed the plug from the heater to see if the heater maybe causing the problem. that made no difference. perhaps the dispenser solenoid is the problem? I’m a little baffled with this one at the moment. Anyone got any other ideas what this could be? Many thanks.
Ashby.

[Ashby]

Re: SMEG DISHWASHER MOD DWF66

Hi Guys, Thanks for your reply. The machine fills ok and starts to wash, then it starts cutting out, only for a few seconds each time. then starts up again for a few seconds and that’s how it goes. I’ve checked the pcb can’t see anything unusual.
Ashby

[Ashby]

Re: SMEG DISHWASHER Mod. DWF 66?

Hi, I’ve had a look at this dishwasher, Tested the dispenser coil and that is ok, tried reseting it without success. whatever program you set it on it will start for about a min or so then it will cut out the display goes off too only for a few seconds then comes back into life for a further few seconds and goes off again. And this is how it goes. I’ve done what P45 has suggested without success. The PCB looks ok too.
HELP! Many thanks.
Ashby

[Ashby]

Re: SMEG DISHWASHER Mod. DWF 66?

Hi, Would someone kindly tell me how to Reset this machine please. Many thanks.
Ashby

[Ashby]

Re: SMEG DISHWASHER Mod. DWF 66?

Hi, Going to have a look at this machine on Sat. Customer says it stops and starts throughout the cycle and drains on a rinse cycle? This’ll be the first smeg i’ve dealt with.Any help will be most grateful. (no error codes showing)
Many thanks.
Ashby.

[Author]

Posts