bazza500

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 1,916 total)
1 2 3 … 5 6 7 … 126 127 128
  • Author
    Posts
  • August 23, 2016 at 6:23 pm in reply to: Beko condenser dryer heating problem #440332
    bazza500
    Participant

    Re: Beko condenser dryer heating problem

    Check that the dryer is not reversing back and forward too frequently. If it is then there is an earth fault confusing the board and this results in no heat. I have had the mains suppressor cause this fault.

    A simple insulation test will rule this out.

    August 18, 2016 at 5:31 pm in reply to: Whirlpool Tumble Dryer 3RLEQ8000KQ2 #440277
    bazza500
    Participant

    Re: Whirlpool Tumble Dryer 3RLEQ8000KQ2

    Spares – Connect
    Tech info – you’re having a laugh 🙂

    August 16, 2016 at 9:11 pm in reply to: beko wmb81445lw #440227
    bazza500
    Participant

    Re: beko wmb81445lw

    Sounds like the typical symptoms of a faulty motor. These machines have a motor with a PCB in them and I don’t know any way of testing them as every pin you try shows as open cct.

    August 15, 2016 at 8:22 pm in reply to: Lamona oven hja3320 #440195
    bazza500
    Participant

    Re: Lamona oven hja3320

    Have you got a product and serial number?

    July 31, 2016 at 11:18 pm in reply to: Samsung RL40PTMG #439767
    bazza500
    Participant

    Re: Samsung RL40PTMG

    The only light lit with the door shut is the little picture of a speaker.

    July 30, 2016 at 4:34 pm in reply to: Samsung RL40PTMG #439765
    bazza500
    Participant

    Re: Samsung RL40PTMG

    no one?

    July 20, 2016 at 9:00 pm in reply to: Induction Hob #439527
    bazza500
    Participant

    Re: Induction Hob

    Are you using magnetic pots?

    July 11, 2016 at 8:20 pm in reply to: Zanussi ZDT21001FA, need advice #439242
    bazza500
    Participant

    Re: Zanussi ZDT21001FA, need advice

    There is a modification to this DW on the pressure switch. This would probably solve your problem.

    July 11, 2016 at 8:16 pm in reply to: Zanussi dishwasher no drain fault #439250
    bazza500
    Participant

    Re: Zanussi dishwasher no drain fault

    Needs a pressure switch mod kit

    July 10, 2016 at 11:00 pm in reply to: Zanussi ZDT21001FA, need advice #439240
    bazza500
    Participant

    Re: Zanussi ZDT21001FA, need advice

    They pipes are the overflow pipes and are clipped it the sump to trigger the overflow switch if the dishwasher overfills. They are not connected together.

    July 5, 2016 at 5:51 pm in reply to: Hoover T/Dryer DMCD1013B-80 Element #439133
    bazza500
    Participant

    Re: Hoover T/Dryer DMCD1013B-80 Element

    40005010

    July 3, 2016 at 8:46 pm in reply to: Whirlpool error codes #439036
    bazza500
    Participant

    Re: Whirlpool error codes

    Inlet valve seems high. I would expect 3.5-4K

    July 3, 2016 at 7:29 pm in reply to: Ikea/Electrolux Renlig DWT 160 3 beeps on starting. #438834
    bazza500
    Participant

    Re: Ikea/Electrolux Renlig DWT 160 3 beeps on starting.

    Put the dishwasher on and leave it for 5 minutes. It could possibly be carrying out a sensor check which can take up to 5 minutes meanwhile it seems to be doing nothing. It should start the program after this pause.

    July 3, 2016 at 6:11 pm in reply to: Ikea/Electrolux Renlig DWT 160 3 beeps on starting. #438832
    bazza500
    Participant

    Re: Ikea/Electrolux Renlig DWT 160 3 beeps on starting.

    Do you have the PNC number?

    June 27, 2016 at 7:14 pm in reply to: Beko WMB81445w #438914
    bazza500
    Participant

    Re: Beko WMB81445w

    They have a PCB inside them. All the wires go to this first so I guess that’s why there is no reading.

    I have had quite a few fail but mist were not allowing any program to be selected.

  • Author
    Posts
Viewing 15 posts - 76 through 90 (of 1,916 total)
1 2 3 … 5 6 7 … 126 127 128