bazza500

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 1,916 total)
  • Author
    Posts
  • in reply to: Grill trips out as it heats! #452721
    bazza500
    Participant

    Re: Grill trips out as it heats!

    I would think the element is going to earth once hot.

    When you say it trips the fusebox. Is it the circuit breaker for the cooker or the main switch for the whole fusebox?

    in reply to: AEG Paddle #452707
    bazza500
    Participant

    Re: AEG Paddle

    If I remember correctly, this machine has a solid plastic base so you’ll need a mirror and magnetic screwdriver to get the screw in.

    in reply to: AEG Paddle #452705
    bazza500
    Participant

    Re: AEG Paddle

    You access the screw through the sump hose hole

    in reply to: Beko WMB81243LB #452650
    bazza500
    Participant

    Re: Beko WMB81243LB

    Just done one this week with exact same symptoms. Board fixed it.

    in reply to: Dryer heater cycle times for AEG 16830 Lavamat Turbo #452637
    bazza500
    Participant

    Re: Dryer heater cycle times for AEG 16830 Lavamat Turbo

    The fan should run continuously once started.

    in reply to: John Lewis JLAFFS20071 Error #452456
    bazza500
    Participant

    Re: John Lewis JLAFFS20071 Error

    Can you give us any other numbers off the rating plate. I can’t tell who makes this from the model number.

    in reply to: Gorenje W7223D W/M Electronic Control Unit Programming #452480
    bazza500
    Participant

    Re: Gorenje W7223D W/M Electronic Control Unit Programming

    You need to count how many times the LED’s are blinking before they pause. This will give you the error code

    in reply to: AEG Dryer E50 Error #452155
    bazza500
    Participant

    Re: AEG Dryer E50 Error

    If I remember correctly you get 2 new caps with the motor

    in reply to: AEG F86050VI dw ‘end cycle light’ flashing, drain pmp runs #452300
    bazza500
    Participant

    Re: AEG F86050VI dw ‘end cycle light’ flashing, drain pmp ru

    Can’t find anything with that model number

    in reply to: AEG Dryer E50 Error #452147
    bazza500
    Participant

    Re: AEG Dryer E50 Error

    Best to go into diagnostics and see which error you get . E5?

    in reply to: Ikea rengora 911 535 057 #451863
    bazza500
    Participant

    Re: Ikea rengora 911 535 057

    Check the insulation of the heater. If it’s low it won’t heat but gives no error codes.

    in reply to: Zanussi ZWF81441W ( 914912316/00) #450411
    bazza500
    Participant

    Re: Zanussi ZWF81441W ( 914912316/00)

    underneath , screwed onto the bottom of the drum. There is no sump hose.

    in reply to: Rangemaster g5 induction. regulator #450369
    bazza500
    Participant

    Re: Rangemaster g5 induction. regulator

    yep , easy job and no programming required

    in reply to: Electrolux ESL6115 – Drains, does not fill. No error #448986
    bazza500
    Participant

    Re: Electrolux ESL6115 – Drains, does not fill. No error

    It sounds to me that your dishwasher is trying to calibrate the sensor.

    Switch it on, start a program and then go and have a cup of tea. It will run in about 10-15 minutes.

    in reply to: Zanussi Dishwasher Flooding #447649
    bazza500
    Participant

    Re: Zanussi dishwasher flooding

    You will probably have to fit the pressure switch modification kit part number 405 53 46-06/0.

    The 2 pipes you are talking about are probably the pipes from the side of the door to the base and are not connected to anything

Viewing 15 posts - 16 through 30 (of 1,916 total)