BobHope

Forum Replies Created

Viewing 15 posts - 226 through 240 (of 1,373 total)
  • Author
    Posts
  • in reply to: hoover dishwasher need part No, for control panel/facia #369448
    BobHope
    Participant

    Re: hoover dishwasher need part No, for control panel/facia

    p/code 32000330 model no. HEDS668 80, control panel part number 49011782.

    Bob.

    in reply to: Wiring on oven help #369438
    BobHope
    Participant

    Re: Wiring on oven help

    just a quick reply, if a fault develops on the oven then the fuse will not blow but the internal componants will fry, just be warned.

    Bob.

    in reply to: Wiring on oven help #369436
    BobHope
    Participant

    Re: Wiring on oven help

    then that is a 30amp supply and your 13 amp cooker shoud not be directly connected to it, please find an electrician with part P and seek his advice on the installation.

    Bob.

    in reply to: Virgin Broadband #369404
    BobHope
    Participant

    Re: Virgin Broadband

    i find the BT wifi hotspots are very handy even in rural areas i can normaly find a hotspot, its BT prices that i disagree with, but you cant have it all ways.

    Bob.

    in reply to: Wiring on oven help #369434
    BobHope
    Participant

    Re: Wiring on oven help

    that looks like a 30amp cooker connection point but may also be a switched spur connection, what kind of isolation switch controls the supply to the oven. ?.

    Bob.

    in reply to: hotpoint indesit #369285
    BobHope
    Participant

    Re: hotpoint indieshit

    pm me an email address and i will send you some info.

    Bob.

    in reply to: hotpoint indesit #369283
    BobHope
    Participant

    Re: hotpoint indieshit

    you just need to recalibrate the pressure switch not reprogramme the module.

    Bob.

    in reply to: Candy CM2136 #369216
    BobHope
    Participant

    Re: Candy CM2136

    the wash heater has a low earth resistance, insulation test on the heater will prove it.

    Bob.

    in reply to: Hoover OPH714D-80 gets to 1 minute #369113
    BobHope
    Participant

    Re: Hoover OPH714D-80 gets to 1 minute

    Martin this is just for testing and yes you will get an E14 but not the other two, best to check the heater with an insulation tester when hot.

    in reply to: Hoover OPH714D-80 gets to 1 minute #369111
    BobHope
    Participant

    Re: Hoover OPH714D-80 gets to 1 minute

    best to disconnect the live and neutral to the heater as there is still an earth path back throuh the water,inner tub and its earthing wire on the tub bearing housing. 😉

    Bob.

    in reply to: hotpoint oven d0891 703150060 #369061
    BobHope
    Participant

    Re: hotpoint oven d0891 703150060

    please check that model number or better get the com code.

    Bob.

    in reply to: Haier hw-c1470tveme-u e3 error #369056
    BobHope
    Participant

    Re: Haier hw-c1470tveme-u e3 error

    has it had the pcb changed by any chance, as it might be programmed to the incorrect model.

    Bob.

    in reply to: Zan FJS1225W – No go #369027
    BobHope
    Participant

    Re: Zan FJS1225W – No go

    worn motor carbons ?.

    Bob.

    in reply to: comet #351745
    BobHope
    Participant

    Re: comet

    and all the D+G and the other insurance work, some one is going to take it on and be rushed off there feet. 😆 making peanuts from a WP no doubt. 👿

    Bob.

    in reply to: comet #351743
    BobHope
    Participant

    Re: comet

    just wondering who will pick up all that work and have the workforce to cope with it ?. any of you inde’s had any increase of work load from repaircare ?.

    Bob.

Viewing 15 posts - 226 through 240 (of 1,373 total)