borderfox100

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 19 total)
  • Author
    Posts
  • borderfox100
    Participant

    Re: Bosch Classixx 1200 Express: Trys to draw water but can’

    Thanks Martin.

    I drained it – then cleaned the filter. There were a couple of pennies in there – nothing else. Replaced filter cap – then ran wash again. It goes straight into ‘wash’ mode immediately – rather than fill tub with water. Once in wash mode, when the tub pauses, it makes a noise as if it’s trying to pump water into it. This action ends abruptly/unsuccessfully. It tries to do this each time.

    Do I need to check the pump itself?

    borderfox100
    Participant

    Re: Bosch Classixx 1200 Express: Trys to draw water but can’

    E Nr. = WAE24162 UK/01

    in reply to: Wanted: Roller Stay for Sharp R-249 Microwave #295249
    borderfox100
    Participant

    Re: Wanted: Roller Stay for Sharp R-249 Microwave

    Thanks. Have popped him a mail. Hopefully he can help.

    in reply to: Water building up at bottom of fridge #285522
    borderfox100
    Participant

    Re: Water building up at bottom of fridge


    @spimps
    : Thanks, will give that a try.

    in reply to: Freezer Door out of alignment #262261
    borderfox100
    Participant

    Re: Freezer Door out of alignment

    I took door off and found problem at base of freezer door. Put a couple of washers on it and put it back – still crooked but may not be as bad. Was only when I had it back on that I realised I can probably hinge from other side as all the slots are there. If current fix hasn’t worked, will probably try hinging from other side..

    in reply to: Freezer Door out of alignment #262260
    borderfox100
    Participant

    Re: Freezer Door out of alignment

    At the very top (above the fridge door) theres a bolt and a metal bracket at the very end.
    Between the two doors, theres a bolt either side of a metal bracket.
    At the bottom of the freezer door, theres just a bracket – no bolt.

    in reply to: Bosch Classixx 1200 Washing Machine – not spinning #256368
    borderfox100
    Participant

    Re: Bosch Classixx 1200 Washing Machine – not spinning

    Simon46 wrote:does the drum turn freely and quietly by hand?

    Yes, thats right.

    superfix wrote:Often the belt comes off due to overloading

    That would be that bloody duvet I tried to sqeeze in there! 😳

    Service Engineer refitted last night. Thanks for your help folks.

    in reply to: Servis Washer/Dryer trips electrics if i try to use dryer #192901
    borderfox100
    Participant

    Re: Servis Washer/Dryer trips electrics if i try to use drye

    For the most part (90{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}) of the time, whenever someone tries to use the dryer, it works (and doesnt trip the RCB) but the clothes arnt drying ie. I dont think they are getting any heat.

    Does this indicate a specific problem?

    in reply to: seal on freezer part of zanussi fridge/freezer.. #183489
    borderfox100
    Participant

    Re: seal on freezer part of zanussi fridge/freezer..

    Turned out that the door was slightly out of line ie. it needed to be tightened up – which I never noticed!

    No new door needed thank god!

    in reply to: seal on freezer part of zanussi fridge/freezer.. #183488
    borderfox100
    Participant

    Re: seal on freezer part of zanussi fridge/freezer..

    Thanks for that Dave. Jeez, these whitegoods parts are bloody expensive 😮

    I’ll have to persevere for a while as funds are tight following house move – but no doubt when the times right(or if the zanussi gets worse!), I’ll be back to order up.

    in reply to: seal on freezer part of zanussi fridge/freezer.. #183486
    borderfox100
    Participant

    Re: seal on freezer part of zanussi fridge/freezer..

    Finally managed to get around to getting back here with the relevant info;


    Zanussi Fridge/Freezer
    Model:Z 56/3 SI
    Product No. 925 881 658
    Serial: 13000088


    Fingers/Legs, etc crossed that its just a seal and not a new door!

    in reply to: Manual for Servis Model No. M9713S #180834
    borderfox100
    Participant

    Re: Manual for Servis Model No. M9713S

    Thanks for that Dave – Appreciate it. The whitegoods manufacturers dont seem to have embraced .pdf manuals much – surprising in that leaving a copy on a website for customers to download is no big overhead – and it certainly beats customers hassling them on the phones, etc.

    in reply to: Manual for Servis Model No. M9713S #180832
    borderfox100
    Participant

    Re: Manual for Servis Model No. M9713S

    Still trying to source this if anyone can help?

    in reply to: Wheels for Whirlpool ADP744 dishwasher… #180018
    borderfox100
    Participant

    Re: Wheels for Whirlpool ADP744 dishwasher…

    gegsy wrote:I see what you mean. ADP744/2 and the 12 NC 854274415410 you have are correct, its the site that is at fault.
    I would email them or use their site to ask them to send you a manual.

    GregWill do. Thanks Greg.

    in reply to: Wheels for Whirlpool ADP744 dishwasher… #180016
    borderfox100
    Participant

    Re: Wheels for Whirlpool ADP744 dishwasher…

    gegsy wrote:Dont put gaps in the 12 digit NC it will be fine then 😉

    Greg
    I tried it with & without spaces Greg and no joy…

Viewing 15 posts - 1 through 15 (of 19 total)