[cab]

Re: Known Test Procedures

Zanussi washer IZ style many models

push button control with or without digital display
FLE14… etc

press both start & skip buttons ( square & triangle)
switch on hold start& skip for 4 secs

display board is checked by lighting each led in sequence.

each press of the fabric button tests functions.

1 fill main
2 fill pre wash
3 fill conditioner
4 hot fill if applicable
5 heating (with circ pump if applicable) max 10 mins
6 checks tub for leaks 250 rpm spin
7 drain and spin to max
8 dry if applicable

end

[cab]

Re: Known Test Procedures

Tricity AW1400 Electrolux Zanussi

press & hold start/pause and any other option button
turn dial 1 step clockwise lights should start to flash after 2 secs

each turn clockwise operates a function
step 2 door lock water thru wash
3 water thru pre wash
4 water thru conditioner
5 does nowt
6 heating max 10 mins *
7 checks tub for leaks, 55rpm clockwise- 55 anti -250 rpm spin
8 drain & spin

turn to position tento display fault code

[cab]

Re: Zanussi TDS483EW Condenser dryer

hi these machines the drum runs on a felt ring only on the front this wears causing a gap which results in a gap appearing at the bottom, either tearing clothes or bepsting marks on them, a modification made to run drun on plastic bearing pads. kit part no. 50272165007

[cab]

Re: Known Test Procedures

beko wma1715s

with power turned off select 90 cotton position
press & hold the start/pause switch on, start button will flash after 3 sec.
each push of start button will test a function
1 all leds flsh
2 water fill thru pre wash
3 water fill thru main
4 water thru conditioner
5 hot fill
6 heater on will fill to level if below
7 clockwise drum to 52 rpm
8 anti clock to 52 rpm
9 drain
10 spin to max
11 fill to check leaks
12 end

[cab]

Re: Known Test Procedures

LG test sequence some models two versions

press Rinse & Spin buttons then turn on.

all lights on display light, each time you press the start/pause button checks a feature,
1 press tumble clockwise 40-50 rpm (shown in display)
2 low speed spin 600-650 rpm (sid)
3 high speed spin uptp max (sid)
4 fill thru prewash water level (sid)
5 fill thru main wash (sid) or hot valve
6 fill thru hot valve (sid) or main wash
7 fill thru dryer if applicable anti clock tumble
8 tumble anti clock 40-50 rpm (sid) or heater
9 heater on for only 3 seca or drain
10 circ pump on or turn off
11 drain pump on
12 turns off

cant test fill on cond compartment!

[cab]

Re: Built in test programs

is there one at the moment?

cab

[cab]

Re: zanussi fjdr1466w

hi just picked this up bit late I know, but did you manage to sort it, this model is on the current version on tds, does it not have a digital display to show the codes? if not the two rows of 4 leds on the extreme right give the code do you know which where flashing?

cab

[cab]

Re: Built in test programs

Hi have you got the Zanussi style. And the Tricity/Electrolux or LG, can help if not.

cab 😀

[cab]

Re: Scary Chinese Dishwashers

anyone had the silicone sealant missing in the top corners behind door seal? water runs down into base activating antiflood. Pants!

[cab]

Re: Zanussi DE540X Dishwasher

Hi Yep there is trouble with the modules, changed a few.

[cab]

Re: Known Error Codes

LG fault code ce have had broken wire on motor plug

[cab]

Re: AW1560W TRICITY BENBIX W/M

Hi these machines dont have a pneumatic lock. If water fills above door then machine is switched off the door can be opened after 2 minutes. The most commmon problem is drain pump. If it goes s/c will blow the board. 😳

[cab]

Re: zanussi zwf 1010w

have you checked the drain pump? should drain first, if pump goes s/c it blows the pcb, so dont just fit pcb without checking pump 😳

[cab]

Re: Zan FJ1254W

have had many problems with user interface pcb, code E90,

[cab]

Re: Fault Codes on AEG Lavamat 74335

weird faults can arise due to motor down to earth.

[Author]

Posts