Forum Replies Created
-
Posts
-
Re: zanussi zwf14280w
if it is a new machine it could be the door lock have been changing a lot recently mostly on machines under 1yr old there is a modified lock available,cant remeber the part number at the min though
Re: AEG Dishwasher F86070VI
check the tacho on the wash motor had one a while back with same prob couldnt get to the bottom of it till different engineer returned and cracked the problem
Re: Anyone know how to get into diag on lux int WD no model
your welcome yes especially check the dryer heater very prone to earth leakage
Re: Anyone know how to get into diag on lux int WD no model
you access diagnostics by with the machine turned of and holding start/pause button and nearest option button turn selector one position clockwise hold down buttons until the leds begin to flash fault codes are displayed at position ten to clear fault code wilst in diagnostics hold start/pause button and nearest option button again it should then go to E00 to exit diagnostics turn selector knob to off again then on and off again it will be ready to go again after you have fixed fault in machine
Re: Tricity Bendix SE501W oven
Service Bulletin
Cooking
Product Group:22
Ref No:CM07005
Subject: ALTERNATIVE MAKE OF SELECTOR SWITCH
Brand: Tricity Bendix, Zanussi, Electrolux, Zanussi-Electrolux
Models:
SE305, SE310, SE323, SE326, CSE327, SE335, SE340,
SE402, SE424, SE428, CSE452, SE452, SB463,
CSE500, SE500/1, SE501, SE501/1, SE505, SE550, CSE551, SE551, SE553, SE558, SE558/1, CSE560,
DDO61CE, EK5361, EKC5044, EKC5045,
ZCE5000, ZCE5001, ZCE5200, ZCE7610
ZKC5030, ZKC5540, ZKC6010, ZKC6020
An alternative make of selector switch (Dreefs) part no. 3890832011 is now available for the models listed above.
This new selector switch has been fitted to all products from serial no. 7170001.
Please note when replacing the original switch with the new alternative switch, the connections remain in the same position with the exception of the white and black wires, which are reversed as shown in the two example illustrations below:
ORIGINAL SWITCH WIRING
REPLACEMENT SWITCH WIRING
Failure to reverse the black and white wire connections will result in the hotplate not regulating correctly.
GBT 06.07 Page 1 of 1.Hope this helps Kaz i cant get the pictures on this part of reply so you can see the way they are supposed to be but it is explained above
Re: AEG W/D
Yes you are thinking right it refers to the one on the condenser to tub hose, check the wires to the ntc they have a habbit of breaking older versions you can re-do the wires with tags but the later ones are idc type blocks.hope this helps
Re: Electrolux ewx 1444w integrated washer dryer
Hi check for earth leakage from the dryer element they are the main culprit on these machines usually have a ed4 fault code with them disconnecting them from the machine will get it running again
Re: Electrolux SF88070VI 91123537400
In addition Cause: w The water protection system (float switch) in the dishwasher has detected an error.
Display: w Text SERVICE CODE i30 is displayed
w The display colour can be red depending on the dishwasher design (e.g. FS).
3 warn tones Solution Switch dishwasher off – assistance is only possible by the customer service!hope this helps basiclly it has water in the base
Re: Zanussi ZCM7902XN double oven
pretty sure main oven will not work without the clock being set so if clock not working then it wont work
Re: Electrolux EWX14440W
what was the error code that came up if it was ed4 try the dry heater for low insulation
Re: ZWD 16270W Cleaning Condenser
they are a right pain you need to remove the front panel,the dryer duct, blower unit hose tub to condenser all fun and will take time
