clockworkone

Forum Replies Created

Viewing 15 posts - 76 through 90 (of 555 total)
1 2 3 … 5 6 7 … 35 36 37
  • Author
    Posts
  • April 15, 2019 at 11:09 am in reply to: Hoover w/m module #461248
    clockworkone
    Participant

    Thank you Dave.

    April 6, 2019 at 8:55 am in reply to: Not repairing any bosch heat pump dishwashers again #460815
    clockworkone
    Participant

    I will not give any warranty on these heat pumps. I explain this to the customer straight away. I show them a picture of part listing from a supplier that in their description says “The problem heat pump from Bosch” Many still go ahead with repair which is great as it is a really handy repair. These have the potential to cost you too much money.

    March 27, 2019 at 11:52 pm in reply to: w/pool interlock #460961
    clockworkone
    Participant

    Thank you Dave.

    February 20, 2019 at 8:29 am in reply to: zan oven temp probe reading. #460579
    clockworkone
    Participant

    Thank you Dave. Appreciate that.

    February 11, 2019 at 10:27 am in reply to: reed switch, rs part no. #460456
    clockworkone
    Participant

    Thank you Dave.

    January 14, 2019 at 8:29 am in reply to: Beko dw module. #459854
    clockworkone
    Participant

    Thank you Dave. Machine is doing a program or part program intermitently. Have gone through usual suspects flowmeter pumps etc. When turning on or off the machine is very slow to react.

    November 21, 2018 at 9:34 am in reply to: Creda cooling fan. #459166
    clockworkone
    Participant

    Thank you Dave that looks like the one. Appreciate the help.Paul.

    October 10, 2018 at 7:03 am in reply to: Zanussi zsf6161s dishwasher #458431
    clockworkone
    Participant

    Thank you Dave. This one has me baffled. 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} heating in wash cycle.But stone cold at end. Had told cust to use intensive wash to test as quick wash prob would not have any drying cycle.Swopped out ntc as I had one with me.I wonder does the same relay turn heat on for wash and drying.

    September 21, 2018 at 4:04 pm in reply to: indesit oven fan motor #458031
    clockworkone
    Participant

    Re: indesit oven fan motor

    Thanks for tip about indesit parts site.Went on and into chat room. Gave all details and it is a c00195669.

    September 21, 2018 at 3:39 pm in reply to: indesit oven fan motor #458030
    clockworkone
    Participant

    Re: indesit oven fan motor

    Thank you Dave and Jim. The motor that is in this oven has 4 lugs that twist fit into oven carcass. I could see parts for serial numbers 25793480100 and 25793480200 but could not see ser no ending 300. Motor looks a little like connect part no 5045382923467. Slightly different connections.can anyone translate that part no for me please. Thanks again.

    September 10, 2018 at 7:56 pm in reply to: Blomberg washer. #457647
    clockworkone
    Participant

    Re: Blomberg washer.

    Thank you Dave for reply and error codes.Module came from Irish supplier. I have asked in the past for them not to send me previously opened modules. This machine is a bit of a head wrecker.Thanks again.

    September 9, 2018 at 11:24 am in reply to: Blomberg washer. #457645
    clockworkone
    Participant

    Re: Blomberg washer.

    Thank you Seamy. This one has me stumped. Tested heater,ntc,water connection,pressure tubes.Replaced dig pr sw as cost was low.No joy.Having thought I had all ancillaries covered i went for new board and guess what,fault still there.Dont want to give up but running out of ideas.

    p.s New board came in a box that i suspect had been opened previously.No bubble wrap or protection inside box. Could I be that unlucky.

    July 18, 2018 at 6:56 pm in reply to: miele W1513 E60 #456786
    clockworkone
    Participant

    Re: miele W1513 E60

    Thank you.

    July 11, 2018 at 7:05 pm in reply to: Miele w1513 carbon brush change #456767
    clockworkone
    Participant

    Re: Miele w1513 carbon brush change

    sorted.

    May 10, 2018 at 1:36 pm in reply to: beko d/w start button #455840
    clockworkone
    Participant

    Re: beko d/w start button

    Thank you Dave.

  • Author
    Posts
Viewing 15 posts - 76 through 90 (of 555 total)
1 2 3 … 5 6 7 … 35 36 37