Criscold

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 816 total)
1 2 3 4 … 53 54 55
  • Author
    Posts
  • April 23, 2016 at 11:13 am in reply to: whirlpool akz151/1x cooker #437261
    Criscold
    Participant

    Re: whirlpool akz151/1x cooker

    Looking at wiring diagram it looks like the motors have a constant live feed and neutral feed from M1 on the board. Possible relay now faulty ?.

    April 12, 2016 at 9:33 am in reply to: Zanussi integrated microwave door. #436980
    Criscold
    Participant

    Re: Zanussi integrated microwave door.

    Hi Steve

    I don’t repair microwaves but I have the manual for this if it helps.

    Colin

    April 11, 2016 at 7:51 pm in reply to: AEG B4140-M2 – 944181386 Hinges #436963
    Criscold
    Participant

    Re: AEG B4140-M2 – 944181386 Hinges

    That’s great Dave, customer will be happy
    Thanks
    Colin

    April 5, 2016 at 7:47 am in reply to: Smeg Dual Fuel Cooker SUK62MFX5 #436725
    Criscold
    Participant

    Re: Smeg Dual Fuel Cooker SUK62MFX5

    Thanks for help eastimark

    February 23, 2016 at 9:51 am in reply to: hotpoint dh53ws #435684
    Criscold
    Participant

    Re: hotpoint dh53ws

    You also have a Cut-In stat for grill mounted on the top panel
    Pt No.C00199515

    February 8, 2016 at 10:46 am in reply to: CDA double oven CD 900/2 BL Grill #435170
    Criscold
    Participant

    Re: CDA double oven CD 900/2 BL Grill

    Hi

    When I wanted a part for a CDA hob I phoned them direct Very helpful and the part was cheaper than anywhere else.

    01949 862012

    Colin

    December 14, 2015 at 5:39 pm in reply to: adg7540 dishwasher w/pool #433718
    Criscold
    Participant

    Re: adg7540 dishwasher w/pool

    – Close water tap and check if F9 still occurs. If so, exchange flow meter.
    – Measure resistor of water inlet valve (WV1) ca. 3,5k?. WV1 should be closed.
    – Check if Output of control board (CB) is permanently switched on. If so,
    exchange CB.

    December 10, 2015 at 10:57 pm in reply to: Leisure RCM110FRXP range cooker #433631
    Criscold
    Participant

    Re: Leisure RCM110FRXP range cooker

    You have mail

    November 6, 2015 at 1:25 pm in reply to: Zanussi W/M E52, Motor or PCB #432260
    Criscold
    Participant

    Re: Zanussi W/M E52, Motor or PCB

    I would check motor connector on board J7 and motor from the control board connector, if ok would go for the board.
    Let me know if you req diagram.

    Colin

    October 25, 2015 at 9:04 am in reply to: aeg f55002v10p/911436014/02 #431879
    Criscold
    Participant

    Re: aeg f55002v10p/911436014/02

    Sent you pm yesterday

    October 19, 2015 at 9:54 pm in reply to: hotpoint dh53x fan runs constantly #431751
    Criscold
    Participant

    Re: hotpoint dh53x fan runs constantly

    You have two cut-in stats on this – one in the top near the cooling fan and one on the rear of the main oven, either would cause this – also it has a feed from the grill switch terminal S2.

    September 16, 2015 at 7:02 pm in reply to: Indesit IDF125 Dishwasher keeps pumping out #430351
    Criscold
    Participant

    Re: Indesit IDF125 Dishwasher keeps pumping out

    No signal from turbine, faulty turbine-wiring or module

    August 14, 2015 at 12:09 pm in reply to: teka dishwasher DW655f1 #429578
    Criscold
    Participant

    Re: teka dishwasher DW655f1

    They have a Web address – teka.com/uk and phone number 01235861916 may be worth a try

    Colin

    August 13, 2015 at 5:04 pm in reply to: Whirlpool ADG7560 D/Washer 854275515879 #429558
    Criscold
    Participant

    Re: Whirlpool ADG7560 D/Washer 854275515879

    Did you lay machine on LH side? Could be water on flow meter contact

    July 3, 2015 at 3:58 pm in reply to: Whirlpool ADG7560 854275515879 draining error #428551
    Criscold
    Participant

    Re: Whirlpool ADG7560 854275515879 draining error

    Did you get the PM I sent yesterday?

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 816 total)
1 2 3 4 … 53 54 55