delta01

Forum Replies Created

Viewing 15 posts - 361 through 375 (of 403 total)
1 2 3 … 24 25 26 27
  • Author
    Posts
  • October 11, 2006 at 12:02 pm in reply to: beko 2 same fault #191766
    delta01
    Participant

    Re: beko 2 same fault

    thanks mike will try that and keep you posted

    john

    September 25, 2006 at 4:13 pm in reply to: beko parts #189600
    delta01
    Participant

    Re: beko parts

    already tried thanks motor was £90 plus vat far too much , i thought may ise would be able to help ?

    September 1, 2006 at 6:33 pm in reply to: elux tds offline dvd #187217
    delta01
    Participant

    Re: elux tds offline dvd

    brilliant ! worked 1st go thanks aqualectric

    September 1, 2006 at 10:08 am in reply to: zan1415w wont start #187073
    delta01
    Participant

    Re: zan1415w wont start

    thanks Cab, board has blown suspected door lock but will check pump , customer went for new machine

    August 31, 2006 at 4:50 pm in reply to: zan1415w wont start #187071
    delta01
    Participant

    Re: zan1415w wont start

    thanks martin hope your right , when the lady explained the fault it sounded like the machine briefly did something then stopped , so i discounted the door lock possibility,

    August 25, 2006 at 1:34 pm in reply to: nef fd 7906 element #186473
    delta01
    Participant

    Re: nef fd 7906 element

    en b1420w0gb/05
    b/ap22/7
    195.312067

    thanks ……..john

    August 25, 2006 at 6:51 am in reply to: Hoover SE220 #186039
    delta01
    Participant

    Re: Hoover SE220

    sorry to contradict but i had one only last week where the dry joint was not quite bad enough and on start up the motor intermittently came on for short bursts , on closer inspection you could see the dry joint flashing

    August 24, 2006 at 5:11 pm in reply to: Hoover SE220 #186037
    delta01
    Participant

    Re: Hoover SE220

    not sure if this is the one with a module in bot left , if it is the module gets a dry joint , you can see it on close inspection of the back of the module, just needs soldering . sometimes its a module replacement only £25 ish from connect

    August 16, 2006 at 9:40 pm in reply to: haier dishwasher hinges #185065
    delta01
    Participant

    Re: haier dishwasher hinges

    thanks guys

    strange thing, with this original post i cant see it on the forum, i accessed the replies from the email .

    August 15, 2006 at 4:05 pm in reply to: haier dishwasher hinges #185062
    delta01
    Participant

    Re: haier dishwasher hinges

    thanks fk will try them

    john

    August 9, 2006 at 8:21 am in reply to: best condenser t/dryers ? #184503
    delta01
    Participant

    Re: best condenser t/dryers ?

    thanks martin

    August 7, 2006 at 12:54 pm in reply to: hotpoint wd71 which panel ? #184190
    delta01
    Participant

    Re: hotpoint wd71 which panel ?

    i stupidly went to this machine without diagnostics info, i now find i dont have the manual anyway ! have taken print out from previous blog on site is this test sequence all thats required ?
    if not
    can you direct me to such info please.

    thanks iadom

    July 31, 2006 at 9:56 pm in reply to: aeg 86700 #183652
    delta01
    Participant

    Re: aeg 86700

    thanks yet again dave . brilliant !

    john

    July 31, 2006 at 2:38 pm in reply to: aeg 86700 #183650
    delta01
    Participant

    Re: aeg 86700

    enr 914 001 126
    fnr 077 / 110913

    thanks dave

    July 27, 2006 at 5:29 pm in reply to: creda / wma type 30mm shaft ? #183354
    delta01
    Participant

    Re: creda / wma type 30mm shaft ?

    thanks for prompt responce dave

    john

  • Author
    Posts
Viewing 15 posts - 361 through 375 (of 403 total)
1 2 3 … 24 25 26 27