electrofix

Forum Replies Created

Viewing 15 posts - 16,666 through 16,680 (of 19,550 total)
  • Author
    Posts
  • in reply to: Beko WMB81445LW #434251
    electrofix
    Moderator

    Re: Beko WMB81445LW

    error come up as

    * BLDC motor card communication error

    dave

    in reply to: Beko DCU9330W #434244
    electrofix
    Moderator

    Re: Beko DCU9330W

    have had a few do this its not unusual. normally i put a spare thermistor in just to check diagnosis but the correct on is riveted to the boared so cant be changed

    element part no 2970101500

    Dave

    in reply to: Beko DCU9330W #434242
    electrofix
    Moderator

    Re: Beko DCU9330W

    chances are its faulty should not be that low


    change the element

    dave

    in reply to: Beko DCU9330W #434240
    electrofix
    Moderator

    Re: Beko DCU9330W

    is your reading of the other sensor with the wires off or on ?

    Dave

    in reply to: bosch cond dryer #434220
    electrofix
    Moderator

    Re: bosch cond dryer

    go here put your Enr in

    http://www.bosch-home.co.uk/store/spareparts/search

    on page 5 of breakdown see item 0510

    my guess is the left side will have to come off. you need to take front panel off the access some of the screws

    Dave

    in reply to: Neff Oven U1442 #434177
    electrofix
    Moderator

    Re: Neff Oven U1442

    form the look of that i would say

    the relays that control the ovens are on the right (2 white blocks with shrack written ontop)

    so join brown and black from relay on left
    and seperately join pink and red from relay on right

    you can get piggy back connectors to help as below

    Dave

    in reply to: Flavel/Leisure cooker ML10FRS #434209
    electrofix
    Moderator

    Re: Flavel/Leisure cooker ML10FRS

    have pm’ed you one

    Dave

    in reply to: zanussi zkc600w tripping the fuse #434188
    electrofix
    Moderator

    Re: zanussi zkc600w tripping the fuse

    elements wont cause that and wiring info for this model is a bit lacking

    1 long shot though. the mains term block at the rear has jumper links on the neutral and live connections. If the installer has not checked these are all tight and they have come loose it can cause this problem

    Dave

    in reply to: Repair Creda T522VW or buy new? #434159
    electrofix
    Moderator

    Re: Repair Creda T522VW or buy new?

    although which does a good job i have seen them recommend some junk over the years
    one of the problems of being an independant repairer is i cant comment on new items as i wont see them for at least 12 months or when warrenty expires

    you could also look at

    http://www.johnlewis.com/bosch-classixx … te/p575576
    machine comes with 2 year guarentee only weak point on these dryers normally is the door handle but they are easy to fit and abouy £5

    Dave

    in reply to: Neff Oven U1442 #434174
    electrofix
    Moderator

    Re: Neff Oven U1442

    if you take the top off and take a photo of the timer connections and post it on here there is a good chance i can tell you which ones to bridge

    Dave

    in reply to: Repair Creda T522VW or buy new? #434157
    electrofix
    Moderator

    Re: Repair Creda T522VW or buy new?

    if you have a vented dryer now why swop if you already have the vent hole in the wall an you can pick them up for about £120

    the WK dryer is an ols whirlpool design built in Halifax and although the door can be a bit weak the units are well designed , cheap to repair , and are better built than the modern Hotpoint,Creda, indesit

    Dave

    in reply to: HOOVER Washing/dryer machine DYNAMIC 6+5 WDNSD #434183
    electrofix
    Moderator

    Re: HOOVER Washing/dryer machine DYNAMIC 6+5 WDNSD

    1 there are 2 heaters so you will prob have 2 faults

    also you can check the heaters with a multimeter both should be under 100 ohms

    Dave

    in reply to: Neff Oven U1442 #434172
    electrofix
    Moderator

    Re: Neff Oven U1442

    most times through the top

    would know more but would need complete model no

    anyway what wrong with it as the only one i looked at was £111 so you dont swop it for no reason
    also you should be able to disable it and bridge it. thats if you dont use it

    Dave

    in reply to: zanussi zkc600w tripping the fuse #434186
    electrofix
    Moderator

    Re: zanussi zkc600w tripping the fuse

    unusual but so it winning the lottery but it happens sometimes

    most of the time tripping is caused by faulty elements

    Dave

    in reply to: bosch exxcel wvt1260gb/01 manual #434185
    electrofix
    Moderator

    Re: bosch exxcel wvt1260gb/01 manual

    http://www.bosch-home.co.uk/customer-se … nuals.html

    Dave

Viewing 15 posts - 16,666 through 16,680 (of 19,550 total)