[gegsy]

Re: bosch wta 3100 no heat

Hi
This model has red reset on back.The element on these are different to other bosch vented dryers. Have had a few of these blown. Has a weird fitting aswell and if you have to change heater be methodical when disassembling.

Heater p/no – 492159

Regards
Greg

[gegsy]

Re: Bosch Condensor dryer – WTL6106GB probem

The carbon brush in contact with the drum completes a circuit and measures the resistance between the paddles and the main drum. If this carbon was to be faulty it would cause a fault in the drying times.

Greg

[gegsy]

Re: Stoves 900GTF Oven – unstable main oven flame

Hi
Flame lift off is due to a lack of oxygen, ie poor room ventilation and will give you a build up of carbon monoxide.
I would cease to use this appliance immediately until you get it checked by a corgi registered installer.
Please use this link to find your nearest engineer Find a corgi installer

Regards

Greg

[gegsy]

Re: Dead WFL2260 after changing brushes

Hi
As previous posts, sounds like motor or other components may be damaged.

There are two makes of motor that could be fitted to your appliance.
May I suggest using the find an engineer link below as the problem you had is rapidly going pear shaped.

regards

Greg

[gegsy]

Re: neff cooker door handle, pt no. please

Hi correct model number B1100WOGB/01.

Door handle is p/no – 284561.
Order from link below

Greg

[gegsy]

Re: Crude But Good

The little fat kid is back trying to sell cookies 😆

http://www.yourdailymedia.com/media/1137764167

Greg

[gegsy]

Re: Getting the brushes out of a Bosch WFL2260

cleudo2006 wrote:Sorry, cancel that – just got it!

you slide them over till the cutout matches up with the holder then it lifts up and out – just wasn’t pulling hard enough.

JIm

Its the getting them back in thats the hard bit 😉 make sure you get the brushes facing the correct angle on the commutator. Best way to check is to offer the brush down the guide until it meets the commutator.Spin the motor shaft by hand, if no horrible clipping noise is heard then it is in the correct orientation.

Greg

[gegsy]

Re: bosch wta 3100 no heat

Hi
You know what Martin you are correct 😳
It does by memory have a re-settable cut out but is only accessible by removing rear panel.

Greg 😉

[gegsy]

Re: bosch wta 3100 no heat

Hi
Here are main things that really tick off any dryer

1/ overloading
2/ blocked lint filter/vent
3/ stopping cycle before last 10 mins of cool down

If any of these are done then activation of the thermal cut out will almost be inevitable. Reset at the rear by pressing the red membrane.

Greg

[gegsy]

Re: Ariston A1535 burnt my clothes!!!

By the last post could the “burn” be an oil mark??

[gegsy]

Re: IPX4???????

iadom wrote:She’s having you on, its on the back of Indesit’s and its short for Manure. 🙂

:tup: :rotl:

[gegsy]

Re: ADP 8242 Error Code E2

Once you take the filters out, in the recess, the black flap is un missable, unless it is missing 😯 I have seen this and would cause this fault 😉
Obviously if its missing you wil be left with a hole approx diameter of the old halfpenny.

Hi Ken, hows Del :wave:

Greg

[gegsy]

Re: ADP 8242 Error Code E2

Its actually a “Sticky” at the top of the dishwasher forum listing viewtopic.php?f=33&t=8046

greg

[gegsy]

Re: Gas Oven will not exceed 155 C

Could be numerous things like door not sealing,thermostat,burner choked etc

I would check our repairs section out due to age and being a gas appliance.

Greg

[gegsy]

Re: ADP 8242 Error Code E2

Hi trukkie
Look at the sticky at the top of this forum 😉

Greg

[Author]

Posts