HotDog

Forum Replies Created

Viewing 15 posts - 256 through 270 (of 397 total)
1 2 3 … 17 18 19 … 25 26 27
  • Author
    Posts
  • March 2, 2011 at 6:34 pm in reply to: sgs45co8/06 #345984
    HotDog
    Participant

    Re: sgs45co8/06

    thanks for info will check it out and cheers for part number

    March 1, 2011 at 10:04 pm in reply to: Hotpoint WT960 Dead #345898
    HotDog
    Participant

    Re: Hotpoint WT960 Dead

    console mod will prob gone get emw to test

    March 1, 2011 at 9:45 pm in reply to: WMA Torx bolts #345916
    HotDog
    Participant

    Re: WMA Torx bolts

    You cannot beat the titanuim drill thanks to Jims tip i have only had to replace it once in two years

    March 1, 2011 at 12:17 pm in reply to: hotpoint wma40 #345890
    HotDog
    Participant

    Re: hotpoint wma40

    are you still at job

    February 22, 2011 at 9:10 pm in reply to: Hotpoint CTD00 Dryer won’t keep running #345291
    HotDog
    Participant

    Re: Hotpoint CTD00 Dryer won’t keep running

    ok but ref to 1st post no relay as described on ctd00 to my knowledge but please correct me if i am wrong

    February 21, 2011 at 9:23 pm in reply to: Hotpoint CTD00 Dryer won’t keep running #345289
    HotDog
    Participant

    Re: Hotpoint CTD00 Dryer won’t keep running

    Not like relay on old dryer its a bitron door lock p/n C00195695

    February 15, 2011 at 9:59 pm in reply to: Hotpoint FFA61 #344736
    HotDog
    Participant

    Re: Hotpoint FFA61

    go round back and see if the hose were the water runs onto drip tray has closed up if so snip off

    February 15, 2011 at 9:53 pm in reply to: Hotpoint F/F FFA52P didn’t restart after defrost #344754
    HotDog
    Participant

    Re: Hotpoint F/F FFA52P didn’t restart after defrost

    I heard on the grape vine the boards are a problem that may not come as a suprise

    February 14, 2011 at 9:22 pm in reply to: Hpt. WMD960 f02 at the end of cycle + some free bonus faults #344420
    HotDog
    Participant

    Re: Hpt. WMD960 f02 at the end of cycle + some free bonus fa

    Iknow you checked earth did you check heater risistance and continuity any way i would connect new heater

    February 14, 2011 at 9:10 pm in reply to: bosch wvti2840gb/04 #343943
    HotDog
    Participant

    Re: bosch wvti2840gb/04

    It was o/c valve didnt see restrictor i just changed coil

    February 13, 2011 at 9:42 pm in reply to: Hotpoint WT746 Stuck at 1 minute? #344555
    HotDog
    Participant

    Re: Hotpoint WT746 Stuck at 1 minute?

    common fault check heater

    February 11, 2011 at 4:45 pm in reply to: bosch wvti2840gb/04 #343941
    HotDog
    Participant

    Re: bosch wvti2840gb/04

    Sorted turned out to be solonid valve it takes about 5min before the valve gets alive feed and if you pause the prog it its same again should have waited longer on first visit

    February 10, 2011 at 5:56 pm in reply to: bosch wvti2840gb/04 #343940
    HotDog
    Participant

    Re: bosch wvti2840gb/04

    got you Jim understand what your saying thank for the info rocketman just didnt get any live feed to valve while on dry thats what confused me should there be a perminant live to valve .Round two 8am fri

    February 9, 2011 at 8:35 pm in reply to: Hotpoint FDW 20 Dishwasher #344132
    HotDog
    Participant

    Re: Hotpoint FDW 20 Dishwasher

    sounds like overload in motor tripping out have look for leak from motor

    February 8, 2011 at 6:13 pm in reply to: bosch wvti2840gb/04 #343937
    HotDog
    Participant

    Re: bosch wvti2840gb/04

    I would just like to know if this is a common fault could it be a board fault its not a model i have worked on before this job has come through a letting company that has all hotpoint machines which i am more at home with and they pay on time so i need sort it any bsh stars out there thanks

  • Author
    Posts
Viewing 15 posts - 256 through 270 (of 397 total)
1 2 3 … 17 18 19 … 25 26 27