johnnyj

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 1,251 total)
1 2 3 … 7 8 9 … 82 83 84
  • Author
    Posts
  • August 21, 2015 at 5:47 pm in reply to: Hotpoint Washer WMFUG842P misbehaving #429693
    johnnyj
    Participant

    Re: Hotpoint Washer WMFUG842P misbehaving

    It has the small linear pressure switch fitted to that machine, have had a load causing this fault, JJ

    July 30, 2015 at 3:23 am in reply to: Hotpoint Aqualtis stopping and lights flashing #429258
    johnnyj
    Participant

    Re: Hotpoint Aqualtis stopping and lights flashing

    Have they disturbed the drain after the bra was removed, might be stuck if the drain is to low works on some but not the main wash.

    July 16, 2015 at 6:28 pm in reply to: Is it just me or is anyone else quiet? #414297
    johnnyj
    Participant

    Re: Is it just me or is anyone else quiet?

    Still plodding along just checked my figures from last year to this year and i’m up at present so cant complain, lost a letting agent when i was on holiday but i havent realy missed them to be honest.

    July 7, 2015 at 6:08 pm in reply to: Hotpoint / Indesit Service Centre #428659
    johnnyj
    Participant

    Re: Hotpoint / Indesit Service Centre

    The problem with the engineer calling when shop is shut is caused by Crm it plans the route and times,also books the parts to which engineer is going to the call, local knowledge is thrown out the window engineers will just follow the times booked by Crm knowing they might not get access.

    July 6, 2015 at 4:51 pm in reply to: Hotpoint HV8B593 #428627
    johnnyj
    Participant

    Re: Hotpoint HV8B593

    On spin does it pump then stop if so I’d be looking at the brushes, they will fill then stop on arcading boards when the brushes are done

    July 2, 2015 at 6:11 pm in reply to: Whirlpool ADG7560 854275515879 draining error #428549
    johnnyj
    Participant

    Re: Whirlpool ADG7560 854275515879 draining error

    Owi sensor gunged up or faulty can cause that, try cleaning it or fit a new one?

    July 2, 2015 at 3:34 pm in reply to: Miele G692SC #428586
    johnnyj
    Participant

    Re: Miele G692SC

    Thanks Seamy i was thinking on these lines not done much work on Miele and was pushed for time cheers JJ

    July 2, 2015 at 5:39 am in reply to: Indesit DIS04 dead #428565
    johnnyj
    Participant

    Re: Indesit DIS04 dead

    More inclined to think it will be the top board?

    June 25, 2015 at 10:50 am in reply to: JLWD1609 PNC 914604321/00 #428429
    johnnyj
    Participant

    Re: JLWD1609 PNC 914604321/00

    Think I had one doing something similar a while back I tried dryer module turned out was a duff valve

    June 16, 2015 at 5:58 pm in reply to: Electrue and their discount software crash, is it just me #428092
    johnnyj
    Participant

    Re: Electrue and their discount software crash, is it just m

    Dont know if anybody else has noticed but i am starting to see some stuff on Qualtex and CDSL are exactly the same, looks to me like one of them is price matching the other.

    May 2, 2015 at 2:18 pm in reply to: Indesit IWDD 7143 #426895
    johnnyj
    Participant

    Re: Indesit IWDD 7143

    Arcadia module wouldnt think motor brushes, you sure its not H20 and a fill problem?

    April 22, 2015 at 6:35 pm in reply to: Apell APWD126 Washer Dryer E13 #426684
    johnnyj
    Participant

    Re: Apell APWD126 Washer Dryer E13

    I think it may be a Smeg machine I was looking for a door seal for one of these turned out it was a Smeg built washer dryer. JJ

    February 25, 2015 at 5:39 pm in reply to: Hoover DYN7164D-80 31005177 Door seal part n/o #424980
    johnnyj
    Participant

    Re: Hoover DYN7164D-80 31005177 Door seal part n/o

    Thanks Jackal

    February 21, 2015 at 6:59 pm in reply to: ID cards #424870
    johnnyj
    Participant

    Re: ID cards

    Been a WTA member for a few years, how do i go about getting an ID card?

    February 19, 2015 at 6:44 am in reply to: Hotpoint WML520P #424812
    johnnyj
    Participant

    Re: Hotpoint WML520P

    Cracked chassis causes a clicking I would check for play on the suspensions where they are attached to the drum new suspensions or a rubber washer from a fill hose should cure Jj

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 1,251 total)
1 2 3 … 7 8 9 … 82 83 84