[laurenceuk]

Re: W/pool D/W ADG450-3 Ser No. 851116115000 Fault Code Requ

Hi Chris,

Thanks for the pointer, if the table is the one by dena89 on the following page:

http://www.ukwhitegoods.co.uk/modules.p … c&start=30

This does not appear to indicate any of the flashing light sequences.

Laurence

[laurenceuk]

Re: What Think You of http://www.tradeplace.com?

Having had another look it appears that to have 4 manufacturers, Electrolux, Bosch/Siemens, Indesit Co and Whirlpool it will cost £340 ish for the first year and then £260 each year after for one licence.

Too much for the amount of times I would use it.

Laurence

[laurenceuk]

Re: Microwave Saisho MW2000 Turntable Motor Required

Thanks for your responses.

Here are the links to the photo`s.

Laurence

http://www.imagestorepro.com/2112224/listings/164.jpg

http://www.imagestorepro.com/2112224/listings/165.jpg

http://www.imagestorepro.com/2112224/listings/166.jpg

[laurenceuk]

Re: Zanussi F/F Prod 924621031…Thermostat

Thanks Pup,

I will give i a go.

Laurence

[laurenceuk]

Re: Zanussi F/F Prod 924621031…Thermostat

Hi Pup,

I don`t know. I have fitted VT9 to some machines in the past that have not always been adequate. I tended to fit gen to Zanussi unless someone can tell me different.

Laurence

[laurenceuk]

Re: Technic Rangemaster Cooker 110DF (100739) Small Oven Ele

Thanks Dave,

Looking on connections the bracket across the centre is a lot `chunkier` than the thin spindle on the one I am working on. Can they be swapped? I can`t remember if the duff one had welded brackets holding the cross piece in place.

Laurence

[laurenceuk]

Re: Whirlpool AWM1404/4 Wash M/c Sticks in Prog

Thanks for your responses.

Re hole in heater:

The isulation reading on this reads about normal, approx 26 ohms if I remember.

Re damage to contacts on heater:

The heater and whole of machine are immaculate inside.

At the price of this PCB, I doubt if they will have it done if it was the problem.

Laurence

[laurenceuk]

Re: New Homes Built in Cooker EL916 Fan Element

Hi, Thanks for all your help on this it is much appreciated.

Laurence

[laurenceuk]

Re: Hvr(Candy)W/drier HW6313MUK Pumps but No Fill?

Thanks Dave

[laurenceuk]

Re: Old Blomberg Wash m/c WA1210…Variable Thermostat

Hmmm,

Is there a number that is in a particular format that can be identified.

Laurence

[laurenceuk]

Re: Old Blomberg Wash m/c WA1210…Variable Thermostat

Hi,

I thought I might have to go out again as the couple are elderly but I remembered the details where in the filter flap so rang them and these are the numbers available.

Typ. WA284AE
Ident No. 17652405
Ser No. 00001282
M300 750/80W ?
Spin 1200rpm

Hope this is sufficient.

Thanks again

Laurence

[laurenceuk]

Re: Old Blomberg Wash m/c WA1210…Variable Thermostat

Thanks Dave,

I have`nt access right now but it is a 9 tag stat in case that helps.

Laurence

[laurenceuk]

Re: Frigidaire Fridge RL5201…Stat Part No?

Thanks Dave

Much appreciated.

Laurence

[laurenceuk]

Re: Hotpoint T/drier 9326…need a cut out!

Hi,

Thanks muchly for your help 😀

Laurence

[laurenceuk]

Re: Smeg Dishwasher DW1612C Error Code?

Hi,

The problem was in fact that the PCB had reset to the factory setting and 2 mins sorted the job out. Prior to receiving this info I had already spent some time looking over the machine….this forum (and its inhabitants 😀 are priceless).

So thanks very much for your input, I am always gratefull…as are my customers 😉 .

Laurence

[Author]

Posts