M1

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 53 total)
1 2 3 4
  • Author
    Posts
  • August 17, 2008 at 7:30 pm in reply to: Plastic bags to protect modules from damp. #259780
    M1
    Participant

    Re: Plastic bags to protect modules from damp.

    Use conformal coating this is used on PCB used in harsh enviroments, Aviation, oil industry & some engine managements systems, usually PCB are dipped in a conformal coating bath, but you can use a spray can.


    4 Quid from Maplin, but be warned if you need to de-solder & rework the PCB it can make it difficuilt.

    http://www.maplin.co.uk/module.aspx?Mod … 5&doy=17m8


    Smells nice to better than Old Spice !! Ha ha !!

    April 13, 2008 at 6:37 pm in reply to: Magnetic Motors #248934
    M1
    Participant

    Re: Magnetic Motors

    Hope this helps !!

    AC motors can be operated in either direction, but the standard AC motor rotation is counterclockwise when facing the end opposite the drive shaft. AC motors can be reconnected to reverse the direction of rotation. This is why many manufactures polorise the connector terminals determining the direction !!

    April 5, 2008 at 8:30 am in reply to: Where there’s a WIL there’s no way! #247819
    M1
    Participant

    Re: Where there’s a WIL there’s no way!

    You need to sprinkle some magic dust on Indesit machines and wave your majic wand !!


    My majic wand is a 4 pound lump hammer !!

    Scraped four Indesit M/C last week !! all under 2 years old !!

    March 15, 2008 at 12:27 am in reply to: Hotpoint WF860 completing program & starting again !! #245927
    M1
    Participant

    Re: Hotpoint WF860 completing program & starting again !

    Thanks Lerch your a star !! 😆

    March 11, 2008 at 10:12 pm in reply to: Indesit TD Model IS60V (vented dryer) #245538
    M1
    Participant

    Re: Indesit TD Model IS60V (vented dryer)

    I did notice that one off these TD had the back two feet missing, it may have buckled the frame, both off these machines have had little use & are under a year old.

    March 11, 2008 at 10:09 pm in reply to: LG wm 1460 FHD & wm 1280 FHD Bearings #245534
    M1
    Participant

    Re: LG wm 1460 FHD & wm 1280 FHD Bearings

    Thanks

    I have undone the center bolt, do I just pull the direct drive off I have tried but it does not seem to move !!

    March 11, 2008 at 9:09 pm in reply to: LG wm 1460 FHD & wm 1280 FHD Bearings #245532
    M1
    Participant

    Re: LG wm 1460 FHD & wm 1280 FHD Bearings

    I want to just change the bearings & seal but can’t seem to figure out how to get the direct drive off !!

    March 6, 2008 at 9:26 pm in reply to: Hoover Condenser Dryer #245136
    M1
    Participant

    Re: Hoover Condenser Dryer

    If you need more info about the relay, contact me I have the correct details & data sheets.

    March 6, 2008 at 9:19 pm in reply to: Hoover Condenser Dryer #245135
    M1
    Participant

    Re: Hoover Condenser Dryer

    The relay’s go on these PCB’s they can be purchased seperatly from a component supplier 240V @ 16 Amp relay

    January 8, 2008 at 9:44 pm in reply to: Hotpoint BWD12 (knob off) #238538
    M1
    Participant

    Re: Hotpoint BWD12 (knob off)

    I do intend to buy a new one but,
    I just can’t seem to get into it to take it off !!

    I think I am going to Dremel the front of the knob off !!

    January 8, 2008 at 12:29 pm in reply to: Hotpoint BWD12 (knob off) #238536
    M1
    Participant

    Re: Hotpoint BWD12 (knob off)

    Hi

    There must be someone out there who knows how I get this knob off ??

    OR do I just use force & break it ?? 😈

    November 3, 2007 at 2:19 pm in reply to: glass washer repair #190515
    M1
    Participant

    Re: glass washer repair commercial appliances !!

    Hi Can anyone help ??

    Hobbart DW Comanda (comercial) customer complains after about 10 cycles just stops. Then they leave it for a couple of hours & it goes again.

    I have checked the PCB for dry joints etc !!

    Any ideas Thanks

    October 29, 2007 at 12:38 pm in reply to: Prima LPR450 Dishwasher. #231782
    M1
    Participant

    Re: Prima LPR450 Dishwasher.

    Just to let you know this is a whirlpool MC made in China, and after using a insulation tester at 500v it picked up a heater fault, which my DVM did not detect.

    Silly me !!

    October 11, 2007 at 11:35 am in reply to: AEG D/W S43070VI (integrated ) #230242
    M1
    Participant

    Re: AEG D/W S43070VI (integrated )

    AEG S5464708 Type EF228 EHP ANC 111 59 41-06 SW DNA24_FR/DMA24_MR

    Yes this is a Zanussi M/C had a look at the PCB no visable blown tracks or components !!

    I have not tested heater/stats yet but if they were O/C would the DW just stop mid programme??

    Thanks again .

    July 26, 2007 at 7:41 pm in reply to: Smeg DW171061 #222321
    M1
    Participant

    Re: Smeg DW171061

    Thanks

    Just done the reset procedure & all works fine.

    Cheers !!!

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 53 total)
1 2 3 4