[M1]

Unfortuanatly I had to take drum out to find hidden screw on front fan housing under drum, then slipped belt over front fan after releasing two motor fixing screws to get movement on front fan, Remember to screw down motor fixing screws and front fan housing in before putting drum back as there is no way you will get a torx screw driver in there even a stubby screw driver.
Took about 2 hours including coffee and talking to the customer..
Made for Manufacture !!
No way made for repair !!
Remeber to quote accordingly for this job !!!

[M1]

Thanks Dave

I have both side panels off and front metal panel off but I can’t get the front fan top half of the housing off , not enough room, without removing the drum which I am struggling to do.
I can’t see how to remove the front plastic assembly, to flex the cabinet to slip belt over drum.,
There must be a easy way or something I am missing.

[M1]

Re: Bosch Heat pump Dryer WTW84560GB/11

Yep

I have read up on them and yes the compressor is getting lukewarm. I shall check for blockages and filters.

Thanks

[M1]

Re: Hotpoint oven SH33X Thermostat & Regulator

The temp dial for oven set to 200 C and only reaches 140 C. Thermostat clicks in and out. I have changed the stat. In the instructions it says its controlled
Fan working fine.

From manual:

Starting the oven
1. Select the desired cooking mode by turning the
SELECTOR knob.
2. Select the desired temperature with the VARIABLE GRILL
knob. See the Cooking advice table for cooking modes
and the suggested cooking temperatures (see Cooking
Modes).
3. When preheating is ?fnished, the THERMOSTAT indicator
light will stay on: place the food in the oven.
4. You may do the following during cooking:
– change the cooking mode by turning the SELECTOR knob.
– change the temperature by turning the SELECTOR knob

http://kitchen.manualsonline.com/manual … s.html?p=3

[M1]

Re: De Detrich American style fridge freezer UN2587/UW1587

This was a motor capacitor problem reduced uF therfore not allways kicking in the motor.

Beware of this strange fault.

[M1]

Re: Beko Tumble Dryer small belt DSV64W

I managed it today with two spoons (handles to lever belt around pulley) shall I keep spoons on the van ?
Maybe some bicycle tyre levers :}

[M1]

Re: Electrolux EWX14450W No display pnc91460600100

Hi

Had a similar fault when I arrived the door would lock you could set the program but nothing happend.
Now the door dose n’t lock !

could it just be the door lock ?

any ideas or tests I can do before I order a PCB as well ?

[M1]

Re: Miele T490 tumble dryer

Thank you for the reply “Fidder” this is all good information for the next time I have this problem.

Thanks

[M1]

Re: Miele T462C tumble dryer (condeser)

Thanks Dave

I have put in a 5V coil relay (instead of the 6V) and noticed the relay next to it, gets about 4.6V.
I need to trace the sequence of events to relise when the pump gets switched on, as I believe I may have been checking for the coil voltage before the processor drives the voltage to the coil.

i shall keep you informed

[M1]

Re: Miele shock absorbers. Can they just go soft?

Yep !

Very common problem take them out and you will see there is no obvious resistance left in them.

[M1]

Re: Miele g1140sc. Dishwasher

Chamber full of muck cleaned out & put on test now it just pumps even when the on/off switch is in the off posistion

hope it’s just damp will leave it for a day to dry out & try again. !!!
👿

[M1]

Re: Brandt Dishwasher VF400JU1/B

Just to let you know on this one the Askoll motor had also failed ! Write off !!!

[M1]

Re: CDA intergrated washer dryer

Model WD001

Fan dryer motor had a fault (disconected all works OK no tripping)

Thanks for your help.

[M1]

Re: Siemens sn26m290gb/02 dishwasher E02

Thanks Martin

Poped a new sugar cube(HF3FD)in the PCB and all working fine !!

[M1]

Re: CDA intergrated washer dryer

Sorry could not find any model number on the machine, but I shall be going back soon. It has a mechanical timer !

[Author]

Posts