MARIO

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 56 total)
  • Author
    Posts
  • in reply to: Hotpoint WT960P counting down but not doing anything #326461
    MARIO
    Participant

    Re: Hotpoint WT960P counting down but not doing anything

    Thanks for help . The drum does not turn ,have been back and checked wires to motor and wires to heater . Heater checks out ok. .The machine does flash up H2O but presume this is because it does not fill . Selected drain counted down from 2 mins to 1min and stayed on 1 minute . Cust said it does count down to end of cycle when she selected prog . Any ideas anybody please.

    MARIO
    Participant

    Re: Larp fridge Model AB5000PV S/N 00NA33140 Power board fau

    Just to say it is a wiring modification required .Pull wire off pin 6 on power board and join to lead from door switch. The other lead from the door switch is fitted to pin 6 on the power board .

    in reply to: Miele dishwasher water level low Model G579SC #317789
    MARIO
    Participant

    Re: Miele dishwasher water level low Model G579SC

    Just to say the fault with this dishwasher was the valve in the fill hose and many thanks to white van man for his help .

    in reply to: Smeg FM38X1 Combi Microwave Oven not programing. #316544
    MARIO
    Participant

    Re: Smeg FM38X1 Combi Microwave Oven not programing.

    Just a thought have you checked door switches are operating ?

    in reply to: Hotpoint WD71 will not start #314865
    MARIO
    Participant

    Re: Hotpoint WD71 will not start

    Cut a flap in plastic cover .Placed blade under the top part of switch and lifted out. Replaced back in position and now switch works . Thanks to you all for all the help on this job .

    in reply to: Hotpoint WD71 will not start #314860
    MARIO
    Participant

    Re: Hotpoint WD71 will not start

    Printed circuit board not blown . How do I replace switch ? Do I peel plastic back to access switch or do I cut through it . Thanks for all replies

    in reply to: Hotpoint WD71 will not start #314858
    MARIO
    Participant

    Re: Hotpoint WD71 will not start

    Thanks for that Madmac will go back on tuesday and try it.

    in reply to: Hotpoint WD71 will not start #314856
    MARIO
    Participant

    Re: Hotpoint WD71 will not start

    Ihave tried a new door lock so if it is the button on the board does it mean new board ?

    in reply to: NEFF dishwasher no heat #310490
    MARIO
    Participant

    Re: NEFF dishwasher no heat

    Just to let you know it was the ntc sensor and dishwasher is now working ok. Thanks to everyone for there help

    in reply to: NEFF dishwasher no heat #310489
    MARIO
    Participant

    Re: NEFF dishwasher no heat

    Checked cables and they seemed ok .Will try sensor thanks to everybody for there help will let you know how it goes

    in reply to: NEFF dishwasher no heat #310486
    MARIO
    Participant

    Re: NEFF dishwasher no heat

    Have replaced timer pcb .Seems to be no voltage at element or stats sensor .Are the sensors available as spare part or do they come complete with element . Thaks to everybody for there help . Thought this job was going to be so easy

    in reply to: NEFF dishwasher no heat #310482
    MARIO
    Participant

    Re: NEFF dishwasher no heat

    Where are the stats ,are they is on top of element with plastic cover over it ? Thanks for helping I need it on this one

    in reply to: Bosch tumble drier not drying properly #306350
    MARIO
    Participant

    Re: Bosch tumble drier not drying properly

    Yes the heater works as sometimes it does go and complete cycle. Water seems to be entering the water collection container ok. The carbon brush is a bit worn so i’ll try that thanks

    in reply to: Zanussi frost free not carrying out defrost #288220
    MARIO
    Participant

    Re: Zanussi frost free not carrying out defrost

    Thanks for trying to help but this model does not have a mechanical timer.
    Is there any way to check pcb, or any way to check any sensors etc.

    in reply to: UN-DW655F1 DISHWASHER #286441
    MARIO
    Participant

    Re: UN-DW655F1 DISHWASHER

    Probably the solenoid on circulation pump stuck you might get away with taking it off and cleaning it

Viewing 15 posts - 31 through 45 (of 56 total)