Forum Replies Created
-
AuthorPosts
-
mike412
ParticipantRe: Braun 4261 Food Processor
Good advice that Martin.
I will keep a sharp lookout at the car boot sales.
regards,mike
mike412
ParticipantRe: Bosch HBN43N550B/01 FD8506
Hi Martin,
Thanks for your prompt reply.
The Stats I refer to are (1) Sheet 2 item number 0249 over on the left hand side.(2) Sheet 7 item number 0709 This one is bolted on to the top oven lamp holder assembly and this is the one I have just changed.
Very observant of you to note that there are two cooling fans, to be honest I had not noticed that. Looks like I just need to change the other “time lag of fan”. (and my glasses). Why two fans?, I dont think i have seen that before.
Regards,
mike
mike412
ParticipantRe: Bosch Heating Element 498607
Thanks for the quick response Martin.
I had tried that old dodge on one of the earlier offerings, but I thought I would give it a Whirl with the one that arrived today. Start reading 1meg- disconnect earth- run for 15 mins-New reading 0.32meg. Verdict-crap elements.
Thanks for your help, I will let you know how i get on.Happy new Year.
Mike.
mike412
ParticipantRe: Hotpoint FFA74P Fridge Freezer
Sounds about right. I am not sure but I dont think that there would be any sort of defrost heaters or such in the lining of the fridge section on this type of fridge. Could this happen through pressure changes due to extreme low temperature? I suppose if the defrost heaters in the freezer overheated it would blow hot air into the fridge compartment. Don’t know really, I can’t wait for the next one in the appartment block to fail so I can be there with my camera, so will the Hotpoint engineer I expect.
Mike.
mike412
ParticipantRe: Neff S51T69XIGB/01 Dishwasher FD8803
Thanks Martin.
Is this a “Tank Off” job, in the manner in which you have so clearly described for the earlier models, or can it be pulled from the side ?.
Mike.
mike412
ParticipantRe: Hotpoint FFA74P Fridge Freezer
Both fridges have gone to the big fridge mountain in the sky.
The first one was the worst, the 4 cuft fridge interior was reduced by about 50 percent. Its the back wall, top and sides. Wish I had taken a picture.Mike.
mike412
ParticipantRe: Bosch WAE24465GB/05
I couldnt find the F63 fault code with a search. Anyone sitting on a list of Bosch fault codes they dont mind sharing?.(pm if you dont want to start a stampede).
regards,
Mike
mike412
ParticipantRe: Hotpoint FFA74P Fridge Freezer
Good Morning.
Any Hotpoint guys out there.
Surely I cannot be the only soul to have met this problem.
Regards,
Mike.
mike412
ParticipantRe: Neff S51T69X1GB/01 Dishwasher FD8803
Noise is there “most” of the time.
I like Bobs idea of running with the spray arms off, got to be worth a try. I was hoping one of our Bosch friends might be able to help with some bedtime reading- any chance.Regards,
Mike
mike412
ParticipantRe: Hotpoint FFA74P Fridge Freezer
Hi Mal. Thanks for the response.
The situation with these two cases are that in both cases it was the same landlord in the same block of flats. These fridges failed during the hot weather and the landlord chose to throw money at the problem and change the fridges to obtain a quick result. What concerns me is what happens if more of these fridges fail. Before that event I would really like to be better informed in respect of the questions that I have raised.
Regards,
Mike
mike412
ParticipantRe: LG WD12336AD Washer Dryer
Yes, that sounds about right. Thanks for the response, Mike
mike412
ParticipantRe: HELP! any BSH guys out there?
Hi Martin.
I had this problem a few months ago.
I got around it quite easily in the end with some plastic “surgery”.
See my post 12th May.
Regards,
Mike
mike412
ParticipantRe: Bosch HBN430550B/02 Oven- Hidden Clock
Thanks Martin.
I have tried this but perhaps I didnt press button for long enough. i will try again.
Mike.
mike412
ParticipantRe: Bosch WAS28466GB/08 w/m Door Handle
Feedback……
It was a problem with the frame 703031 not matching with the handle.
I took a gamble in the end and removed the 3-4mm “indent” around the edge where the handle fits. (difficult to describe but obvious when you have the part to hand) This is soft plastic, easily worked and I achieved a good result. Worked fine from thereon.
Job done.
Mike.
mike412
ParticipantRe: Baumatic B205SS-A Oven
No Baumatic Guys around at the moment?.
Mike.
-
AuthorPosts
