Forum Replies Created
-
Posts
-
Re: north west based work
Ok I’ll tell him to check them out does anyone one do agent work for manufactures these days or is it all in house ?
I told him to contact insurance companies for work any other good agents out these to do work for?Re: north west based work
postcodes preferred would be wn1,2,3,4,5,6,7,8
wa1,2,3,4,5,6,7,8,9,10,11,12
other post codes local to these would also be considered
17 years experience of whitegoods repairs including washers,d/washers, dryers, ovens, microwaves, steam ovens, fridge freezers, hobs, cooker hoods
how ever not gas repairs or fridge systems repairs
thanksRe: F gas Certification
Really oh that’s great I know a few fridge guys so I can spend a few days with them when I next get chance
ThanksRe: defrost not working on siemens frost free fridge freezer
ThAts great !!!
Maybe at the time of the last repair they where not aware of the ful proceedure neededRe: defrost not working on siemens frost free fridge freezer
If its a free standing siemens fridge then u may have a 5 year garrantee
If not I would consider giving them a call and expressing your concern that it’s still not working correctly from when they last repaired it even though it was years ago if u push then they should offer a free inspection to check it has had the correct modifications to
Help it defrost as it should
Good luckRe: F gas Certification
Hi guy sorry to bring this up again time has gone by since this was discussed but here’s my scenario I have 12 years experience of repairing appliances and understand the procedure and principle of refridgeration but have never carried out gas repairs.
What is the legal requirement don’t really want to sit though a long course as I know the basics but have always passed re-gas/compressor work
On now I would like to add this skill to my bow what do I need to do
Your help would be appreciated
MikeRe: dyson cr01 noisey in contro rotor mode???
Hi Dave spoke to a few people who have said the same since thanks for ur reply
Re: Bosch w/dryer wft2806 1 min and anti crease light flashi
hi you’ll have to confirm this next time you go back but the 1 minute and anti-crease fault usually also flashed the wash light too
this it pump time exceeded
white pump get it changed!!!Re: bosch washer error code
hi there no you’ll find there is alot of differnet error codes to confuse you!!!! ha ha lol
f01 on your model is door open!! or door lock
door lock part num:182154 usually bout 20 quid
mikeRe: Bosch SGV56A03GB/12 Dishwasher
i know this is not what you want to hear but i can only think the module as it wont reset i suspect you have removed and examined the module??
i would put money on it?
the only other time ive had the fill and empty fault and its not been the impellor jug ive found the circ motor jammed or faulty but the module would still reset i guess you need to bite the bullet and fit the moduleRe: Bosch WTE84107gb/02 (fd8602)
Hello again,
Ok the ntc is situated behind the air vent on the bottom right hand side to get the cover open panel for the condenser and then lean appliance back and you’ll find 3 plastic clips to release it you need to be pulling on it also for it to move behind that panel is the filter ntc
Resistances:- 32k at 0c
10k at 25c
0.69k at 100c
Part number 154166 there around a tenner
Good luckRe: Bosch dishwasher SRV43M03GB/24 Removing impellor on wash
hi there
yes i usually carefully place a screw driver in the back of the motor to stop it moving then grab the impellor with my other hand and it should screw off in an anti clockwise direction once this is off you should be able to pull off the rubber outer seal and the lift off the plastic housing and carefully sprize out the centre carbon face seal.
then just put it back in reverse
good luck
