paddyd99

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 27 total)
1 2
  • Author
    Posts
  • March 18, 2010 at 4:55 pm in reply to: hotpoint aquarious wd440 #315213
    paddyd99
    Participant

    Re: hotpoint aquarious wd440

    no visable damage to the module, no damage to wires, customer said it did trip the breaker just before fault appeared..

    January 29, 2010 at 2:11 am in reply to: whirlpool washing machine starts to fill then stops. #310247
    paddyd99
    Participant

    Re: whirlpool washing machine starts to fill then stops.

    Thanks for the tips guys, went at it today and checked all wiring for breaks and so on, all was good. I had a different module from a whirlpool ber in the shop so I whacked it in and of she went…The module I used doesnt have the old machines cold wash function or variable spin speed sockets but its working fine. Its a shame that whirlpool continually price these boards way beyond any decent kind of price. Thanks again.

    January 28, 2010 at 1:47 am in reply to: whirlpool washing machine starts to fill then stops. #310244
    paddyd99
    Participant

    Re: whirlpool washing machine starts to fill then stops.

    I deemed this machine ber today so its slap bang in the middle of my workshop…….Its getting fixed, hell or high water, come on guys take a stab at it……..anyone? 🙂

    January 26, 2010 at 9:22 pm in reply to: whirlpool washing machine starts to fill then stops. #310243
    paddyd99
    Participant

    Re: whirlpool washing machine starts to fill then stops.

    Just checked the price of a programme for the above machine 218 pounds plus vat from connect, thieving DGFHDGo’;dvujdvjDV ERSS.

    November 1, 2009 at 10:44 pm in reply to: hoover pe235 washer #302184
    paddyd99
    Participant

    Re: hoover pe235 washer

    many thanks

    October 20, 2009 at 11:28 am in reply to: whirlpool AKZ2516nb f03 fault #299880
    paddyd99
    Participant

    Re: whirlpool AKZ2516nb f03 fault

    thanks jackster, anyone else out there got any experience of these?

    September 9, 2009 at 9:32 am in reply to: beko wma510w #296610
    paddyd99
    Participant

    Re: beko wma510w

    many thanks guys

    September 8, 2009 at 8:36 pm in reply to: siemens washer dryer #296357
    paddyd99
    Participant

    Re: siemens washer dryer

    Hi Martin, took a look at that washer dryer today. Its a WDI1440GB/03 integrated jobby……Punter says that the E14 error comes up at various stages of the wash or dry cycle then stops….Ntc is in the vent of the door seal, theres a ready there allright but its obviously dodge at a certain temp threshold. Sound right to ya Martin? Same part number as posted previously?
    Paddy

    September 7, 2009 at 8:57 am in reply to: siemens washer dryer #296356
    paddyd99
    Participant

    Re: siemens washer dryer

    Thanks Martin. Will confirm when I get out there for a look.

    September 5, 2009 at 1:03 am in reply to: Common Refrigerator Hints #151047
    paddyd99
    Participant

    Re: Common Refrigerator Hints

    great post dpr, many thanks.

    September 5, 2009 at 12:52 am in reply to: Hoover HNL8146-80 #295245
    paddyd99
    Participant

    Re: Hoover HNL8146-80

    test for resistance thro the tacho…..possibly an open winding on the motor??

    September 5, 2009 at 12:50 am in reply to: t/bendix d/washer #296259
    paddyd99
    Participant

    Re: t/bendix d/washer

    Could be a dry joint on the pcb heater relay????….eventually it wont pass the wash cycle.

    September 2, 2009 at 11:37 pm in reply to: whirlpool adg4500 #295586
    paddyd99
    Participant

    Re: whirlpool adg4500

    Let me know how you go with the soldering iron…..this machines pretty new and at the moment its a scrapper in my workshop…..shame to bin it…everything pointing to the pcb but I aint replacing it as the askoll motor hasnt been replaced in it yet either….Im sure its ready to blow should I put replace the pcb 🙂

    August 27, 2009 at 8:04 am in reply to: whirlpool adg4500 #295583
    paddyd99
    Participant

    Re: whirlpool adg4500

    thanks penguin

    August 4, 2009 at 12:49 am in reply to: Changing bearings on a Zanussi Aquacycle 1200 F 1245 W #293524
    paddyd99
    Participant

    Re: Changing bearings on a Zanussi Aquacycle 1200 F 1245 W

    Give me a shout byrne if you havent binned her yet…..there a great machine and worth a repair. Im in Galway if it suits.
    Paddy

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 27 total)
1 2