Penguin45

Forum Replies Created

Viewing 15 posts - 15,646 through 15,660 (of 19,678 total)
  • Author
    Posts
  • in reply to: diplomat adp8242 #168950
    Penguin45
    Participant

    Re: diplomat adp8242

    It thinks there’s a fault with a part that isn’t there……… 🙄

    Check this:

    http://www.ukwhitegoods.co.uk/modules.p … ic&t=12619

    Post #4 explains the procedure required (Same basic appliance).

    Regards,
    Penguin45.

    in reply to: “Ooooh Matron” ? #164487
    Penguin45
    Participant

    Re: One to keep an eye on.

    I suspect that he may well work for F+P, but he ain’t an engineer. Sorry, we’re technicians now. 😀 He is now posting in the Oz forum and isn’t exactly helping – doesn’t read the thread for a start. I think I’ll have to peck him soon……

    Chris.

    in reply to: Ikea/Whirlpool dishwasher 60cm wide and integrated #168829
    Penguin45
    Participant

    Re: Ikea/Whirlpool dishwasher 60cm wide and integrated

    Please – tell us the numbers on the label on the edge of the door……. Also, the pattern of flashing lamps (1-2-3 pause repeat, for instance).

    Penguin45.

    in reply to: Bosch SGS5358GB/17 #168881
    Penguin45
    Participant

    Re: Bosch SGS5358GB/17

    Thought Gegsy might have answered this by now – he’s so naughty. 🙄

    Right. This machine uses the “mushroom” water level control system, and basically it gunges up over time. The official repair is to replace the “mushroom” and the control board, which has new software allowing for a higher water level.

    A job best carried out by BSH if the machine is under two years old, click the link below for an independant if it’s older.

    Power off if investigating……….

    Regards,
    Penguin45.

    in reply to: Diplomat ADP8322 #168891
    Penguin45
    Participant

    Re: Diplomat ADP8322

    This is a Whirlpool machine – the reset procedure is very simple. Simply hold the “Start” button down for about 5 seconds – programme will abort, drain pump will run for one minute and then programme can be reset.

    From what you have described, you have a thermistor (or NTC) failure. This is an awkward little problem to solve, but relatively inexpensive. Pro help is the best option – click the link below.

    Power off if investigating further.

    Regards,
    Penguin45.

    in reply to: Wanted Ignition Unit for Hygena AHY1120 #168892
    Penguin45
    Participant

    Re: Wanted Ignition Unit for Hygena AHY1120

    P/no is HYGHRIGNITORE or 14HY97 depending on source. Can’t find a current price; email to spares@ukwhitegoods.co.uk for prices and ordering.

    Regards,
    Penguin45.

    in reply to: zanussi rear 1/2 tub #168884
    Penguin45
    Participant

    Re: zanussi rear 1/2 tub

    4 different ones – model number?

    Chris.

    in reply to: fisher & paykel when agitator hit the sides #168756
    Penguin45
    Participant

    Re: fisher & paykel when agitator hit the sides

    Don’t think OOB is in circuit until spin sequences…. Motor running too fast in wash? Suspa rods not on correctly?

    Penguin45.

    in reply to: Indisit WIL 103 #168877
    Penguin45
    Participant

    Re: Indisit WIL 103

    Given that EMW’s boards are £35-40 typically, the job instantly becomes much more affordable………

    Chris.

    in reply to: ISE Washer Now Available #166288
    Penguin45
    Participant

    Re: ISE Washer Now Available

    NEC

    in reply to: Ikea/Whirlpool dishwasher 60cm wide and integrated #168827
    Penguin45
    Participant

    Re: Ikea/Whirlpool dishwasher 60cm wide and integrated

    Water level is controlled either by air pressuer into a diaphragm switch or by a flow meter, depending on the model number……..

    Regards,
    Penguin45.

    in reply to: Bosch Exclusiv F1100A #168879
    Penguin45
    Participant

    Re: Bosch Exclusiv F1100A

    Can’t get anything to flag – drag it out, there’s another label on the back 😀

    Chris.

    in reply to: Zanussi FL1084 – 914780083 #168855
    Penguin45
    Participant

    Re: Zanussi FL1084 – 914780083

    Stuck relay on board’s a good bet.

    Chris.
    Edit: Wrong, this one is switched straight off the Elbi timer, via the p/switches. Been a long day…….

    in reply to: Hoover HW 160 washer dryer #168850
    Penguin45
    Participant

    Re: Hoover HW 160 washer dryer

    :wave:
    You again………… 😀

    in reply to: Hoover HW 160 washer dryer #168848
    Penguin45
    Participant

    Re: Hoover HW 160 washer dryer

    91620118.

    Chris.

Viewing 15 posts - 15,646 through 15,660 (of 19,678 total)