Forum Replies Created
-
AuthorPosts
-
RickT
ParticipantRe: Whirlpool ADG7550 11 flashes?
Hi Simon, 11 flashes points to optical water sensor in sump, although I,ve come across this where machine had leaked into base on to wash pump terminals and blown the pcb. Worth checking this for any blown tracks. Hope this helps
RickRickT
ParticipantRe: Bosch dishwasher SGV43A03GB/44
I did test the switch and all seemed ok!
RickT
ParticipantRe: Bosch dishwasher SGV43A03GB/44
Thanks Martin. Have you found this a common problem with these as this is the first time for me?
RickRickT
ParticipantRe: Stoves 900EF main oven hinge probs.
Thanks for the info. Will try your suggestion first as Connect has no stock at present.
Cheers RickRickT
ParticipantRe: Stoves 900EF main oven hinge probs.
Come across one of these today with exact fault Door loose and not closing at top . Was interested to know if fitting the hinge kit (5031685826840) did the trick or would just fitting the ‘L’ shaped hinge bars (5031683784036) solve the problem?
RickT
ParticipantRe: Hoover D7190 pump required
Thanks for reply. Have found Espares show stock. Will give them a try.
RickRickT
ParticipantRe: Hygena/Smeg APL8214/4 dishwasher
Thanks for the extra info. I’ll give it a more thorough look as I was a bit pushed for time yesterday.
Cheer RickRickT
ParticipantRe: Hygena/Smeg APL8214/4 dishwasher
Thanks for reply. I’ve checked the four hoses that connect towards the front end of the reservoir. Blowing through them with no great resistance (except water valve intake!!).Have advised customer to try running a cleaner through it. Had this problem with the older Bosch design and it was always the sump feed pipe either blocked or crushed underneath causing it to leak on the filling stages but this one only leaks once the wash action has started. Water level is coming up to the ledge just above the filter if that means anything. There is a small channel in the centre of the reservoir that may be blocked but looks impossible to clean.
Cheers RickRickT
ParticipantRe: Rangemaster 110 Ceramic Cooker
Ok , finally found part number after many phone calls. Thought it may come in usefull for anyone else that comes across this one. Module PCB cooling fan FVLP027589
RickT
ParticipantRe: Rangemaster 110 Ceramic Cooker
Still having great diificulty getting this part number. Connect have drawn a blank. This module is about the same size as a stick of pc ram with half a dozen or so wires soldered to it. Help would be much appreciated.
RickRickT
ParticipantRe: Rangemaster 110 Ceramic Cooker
There’s been some spillage down the back which has found its way into the box and shorted the pcb. There’s no supply to the fan oven main switch and also the customer did complain about the constant humming from the cooker when not in use which I took to be the cooling fan.
Thanks for the reply
RickRickT
ParticipantRe: Ikea/Whirlpool DWF417W fault code
Thanks Chris, I’ll give it a go!
RickRickT
ParticipantRe: Ikea/Whirlpool DWF417W fault code
Not quite sure what this refers to (E7 – 1st, 2nd, 3rd flashing – flow meter detected when not fitted – reset required. ) and how to reset this one.
RickRickT
ParticipantRe: Diplomat ADP8322 dishwasher FA fault code
Hi Greg
Revisted this machine today. On starting progamme, waited for it to fill and show error FA. Checked circuit from pcb WI connector down to water indicator and back, all was fine (closed circuit). Can I assume that the fault is in the pcb as I’ve tested all other components??
Cheers RickRickT
ParticipantRe: Stoves 600GTF gas cooker cooling fan
Hi Greg
The fan motor (open circuit) on this model is situated on the bottom right (viewed from rear) has a large black plastic fan with a concave rear edge which locates into the venting hole on the back panel. The wires run across to the pcb on the left.
Thanks Rick -
AuthorPosts
