robbo1973

Forum Replies Created

Viewing 15 posts - 151 through 165 (of 644 total)
1 2 3 … 10 11 12 … 41 42 43
  • Author
    Posts
  • October 12, 2010 at 9:27 pm in reply to: SMEG DI612C #332720
    robbo1973
    Participant

    Re: SMEG DI612C

    thanks very much.

    October 11, 2010 at 6:10 pm in reply to: smeg A2 #332250
    robbo1973
    Participant

    Re: smeg A2

    cheers for reply mark do you know a supplier as electrue are a waste of time at mo?

    cheers chris

    October 9, 2010 at 10:28 am in reply to: diplomat adp 8252 #332444
    robbo1973
    Participant

    Re: diplomat adp 8252

    cheers any idea on fault code?

    October 7, 2010 at 7:08 pm in reply to: wte84102gb/05 #331718
    robbo1973
    Participant

    Re: wte84102gb/05

    went here and pulled it into the w/shop today.
    the machine runs fine then after a minute or two the whole thing shuts down switch off and back on and still nothing waited about 5 mins and it was back this time ran for about 20secs and done it again.has anybody had anything like this before,could this be a cut out? any advice appreciated before i start pulling it apart.

    cheers chris

    October 6, 2010 at 9:29 pm in reply to: s20btsb21ag #332256
    robbo1973
    Participant

    Re: s20btsb21ag

    this cust inherited machine about 1 year ago with the house so does not know age.can anyone tell by 85 number?

    cheers chris

    October 6, 2010 at 9:28 pm in reply to: 858615215001 #332253
    robbo1973
    Participant

    Re: 858615215001

    thanks

    September 27, 2010 at 7:38 pm in reply to: candy cpca 240 fsk f/f #252195
    robbo1973
    Participant

    Re: candy cpca 240 fsk f/f

    a general rule of thumb i use on these as long as it is freezing round the whole plate so it is not short of gas then turn off by module,if it shuts down then the sensor has failed however if it continues running even if set to off then change the pcb,
    this has never failed me so far 😀 .

    cheers chris

    September 13, 2010 at 6:27 pm in reply to: Leisure Roma 100 Range cooker – Thermal links in wiring? #330232
    robbo1973
    Participant

    Re: Leisure Roma 100 Range cooker – Thermal links in wiring?

    hilly is spot on really common problem i fit loads of these.

    September 3, 2010 at 2:55 pm in reply to: bosch wae24162gb/03 #329422
    robbo1973
    Participant

    Re: bosch wae24162gb/03

    thanks lads.

    as long as theres no swimming pool around 😉


    cheers chris

    August 17, 2010 at 9:41 pm in reply to: BOSCH WFF0220 #327534
    robbo1973
    Participant

    Re: BOSCH WFF0220

    thanks for replies it was a dry joint on the board causing no heat.

    August 15, 2010 at 8:28 pm in reply to: hotpoint bwd129 fault code #327855
    robbo1973
    Participant

    Re: hotpoint bwd129 fault code

    thanks jim 😀

    July 29, 2010 at 9:56 pm in reply to: stoves 444448194 #326224
    robbo1973
    Participant

    Re: stoves 444448194

    thanks 😀

    July 26, 2010 at 4:25 pm in reply to: ge american psg27nhsacbb #310353
    robbo1973
    Participant

    Re: ge american psg27nhsacbb

    fit new fan and pcb at end of may and cust been back on saying slightly noisy and temp erratic are there any commion probs or is it a case of seeing whats going on any advice appreciated.

    July 21, 2010 at 3:22 pm in reply to: lg f1403rd6 #325833
    robbo1973
    Participant

    Re: lg f1403rd6

    thanks helo,is this an import?office rang connect and they say that the door seal is obsolete.has part number been superseeded

    July 9, 2010 at 10:03 pm in reply to: beko wm1715s #325043
    robbo1973
    Participant

    Re: beko wm1715s

    thansk jim

  • Author
    Posts
Viewing 15 posts - 151 through 165 (of 644 total)
1 2 3 … 10 11 12 … 41 42 43