Page 2 – UK Whitegoods

Forum Replies Created

Viewing 11 posts - 16 through 26 (of 26 total)

← 1 2

Author

Posts
January 4, 2011 at 7:41 pm in reply to: Hotpoint Engineer’s Quick guide #339889

robstech
Participant

Is it possible this model is aborting the spin cycle because of a too small load or an out of balance load? Have you tried spinning a test load?

January 4, 2011 at 11:21 am in reply to: Atag american fridge freezer #340058

robstech
Participant

Re: Atag american fridge freezer

Are you sure it is not Maytag? Check this link http://www.appliance-parts-warehouse.co … JRBEWH.cfm

January 4, 2011 at 10:17 am in reply to: Zanussi ZDT 5053 – Dishwasher #338305

robstech
Participant

Have you checked the 13amp mains connections and switches?

November 30, 2010 at 7:37 pm in reply to: Candy CIC324 AK fridge too cold #291970

robstech
Participant

Re: Candy CIC324 AK fridge too cold

TeeMyob wrote:

snig wrote:
Been back with thermistor and info only to find thermistor is not where indicated. measured very carefully but just not there! very annoying as still the same amount of work involved. Be warned!!!!!

Occasionaly they are nowhere near where they are suggested to be.

Hi

any information regarding the possible location of the fridge ntc would be appreciated.

Regards
Rob

June 11, 2010 at 11:22 am in reply to: Zanussi ZDC 46130 Error code #322094

robstech
Participant

Re: Zanussi ZDC 46130 Error code

Thanks for the gen. Can the triac be be replaced or does it need a new board?

Cheers

February 26, 2010 at 9:17 am in reply to: Whirlpool ADG 450/3 aborting #312771

robstech
Participant

Re: Whirlpool ADG 450/3 aborting

Anti flood device fitted, all checkable electrics test ok with meter.

June 11, 2009 at 11:22 pm in reply to: Hotpoint DWF70S AL02 fault after fitting drain pump #288962

robstech
Participant

AL02 = Valve or connections

June 11, 2009 at 11:12 pm in reply to: Whirlpool “not spinning sometimes” #288659

robstech
Participant

Its probably aborting an out of balance load, ask customer if she notices it missing the spin more often on small loads.

June 11, 2009 at 11:03 pm in reply to: Amana XRSS287B american side by side PCB query #288793

robstech
Participant

Thanks for the gen..

December 15, 2007 at 3:09 pm in reply to: Whirlpool American Fridge Freezer broken down – help! #141999

robstech
Participant

Re: Whirlpool American Fridge Freezer broken down – help!

I found some 1000uf 6.3v caps for c3 on Front pcb on ebay..My local Maplin didn’t have any.
Does anyone know what the fault code “d” on the fridge temperature display means?

December 12, 2007 at 11:24 am in reply to: Whirlpool American Fridge Freezer broken down – help! #141996

robstech
Participant

Re: Whirlpool American Fridge Freezer broken down – help!

Hi everyone

Anyone know the value of Cap C3?

Regards
Robert

Sk1p_Rat wrote:Hi all,

It’s fixed 😀 . My fridge no longer flashes all for 25p.

On the front control board there is a Cap C3 on my board it was slightly bulged like you get on a duff motherboard. I’ve changed it and no more flashing.

BTW does anyone want to buy a rear board for a S20BRSS31-A/G part no 481221778192?

Regards

Paul
Author

Posts

Viewing 11 posts - 16 through 26 (of 26 total)

← 1 2