SimonCD

Forum Replies Created

Viewing 15 posts - 1 through 15 (of 119 total)
1 2 3 … 6 7 8
  • Author
    Posts
  • November 30, 2014 at 11:59 am in reply to: Siemens tk76k572gb/02 coffee machine- aborts milk froth #422099
    SimonCD
    Participant

    Re: Siemens tk76k572gb/02 coffee machine- aborts milk froth

    Thanks Martin, I had tried multiple descaling progs, purchased some stuff that dissolves milk proteins and tried that too.
    Lee, you wee dead right! although the steamer tip looked ok from the front, when I stripped it there was another hole on the side, hidden from view, and it was totally blocked!
    I have now had about six coffees to celebrate and am feeling a bit wired!
    Thanks all 😉

    July 31, 2014 at 4:26 pm in reply to: Electrolux washer dryer ewx14450 displaying e68 fault #417351
    SimonCD
    Participant

    Re: Electrolux washer dryer ewx14450 displaying e68 fault

    cheers will do 🙂

    September 19, 2012 at 11:09 am in reply to: Electrolux part identification online #381482
    SimonCD
    Participant

    Re: Electrolux part identification online

    Thanks Seamy, bloomin shame 🙁

    July 11, 2012 at 3:48 pm in reply to: Benefits of joining tradeplace? #378020
    SimonCD
    Participant

    Re: Benefits of joining tradeplace?

    Thanks for your speedy response! it did seem too good to be true 🙁

    April 19, 2012 at 7:35 am in reply to: Hotpoint t622cw Timer conversion kit – diagram missing #373446
    SimonCD
    Participant

    Re: Hotpoint t622cw Timer conversion kit – diagram missing

    Thanks Jim. Good find! thanks very much.
    Simon 🙂

    August 15, 2011 at 4:50 pm in reply to: Oh Helen where did I go wrong? #357109
    SimonCD
    Participant

    Re: Oh Helen where did I go wrong?

    LOL, dont forget to lift the tab back up before inserting the new one 😉

    July 24, 2011 at 12:01 pm in reply to: Hotpoint aqualtis aq9l29i fault code #356030
    SimonCD
    Participant

    Re: Hotpoint aqualtis aq9l29i fault code

    Problem identified!
    Thanks Jim, much appreciated 🙂

    June 10, 2011 at 11:55 am in reply to: Veolia #353281
    SimonCD
    Participant

    Re: Veolia

    lol, we use biffa, they charge £70! when i complained they cancelled it.

    May 7, 2011 at 10:44 am in reply to: Qualtex troubles #350647
    SimonCD
    Participant

    Re: Qualtex troubles

    Hi Martin, The goods were signed for in the usual way and i was unaware that they were sent “at my own risk” until i complained about the dent! I recieved my delivery, as always by courier to our shop not qualtex van.

    May 6, 2011 at 4:53 pm in reply to: Qualtex troubles #350643
    SimonCD
    Participant

    Re: Qualtex troubles

    I have now written to Qualtex asking them to clarify their position on damaged bulky spares and finished goods so hopefully it will all be resolved soon!

    May 6, 2011 at 7:33 am in reply to: Qualtex troubles #350640
    SimonCD
    Participant

    Re: Qualtex troubles

    It was the manchester office and funny enough i heard back this morn from a Mr Eatherington confirming that although this is the case they would arrange a £10 credit. I think this only applies to finished goods and not spares.
    A real shame i think as i have, until now, found Qualtex a pleasure to deal with.

    February 1, 2011 at 6:26 pm in reply to: Fault Code Guide #340871
    SimonCD
    Participant

    Re: Fault Code Guide

    Brilliant! Thanks

    November 8, 2010 at 5:41 pm in reply to: Clamp on Ammeter questions #335233
    SimonCD
    Participant

    Re: Clamp on Ammeter questions

    When testing solid hotplate cookers you can easily see that all power settings work properly, Check to see if that heater you just fitted is working with no troublesome probing or even getting near the heater.
    Best tool ever!

    October 11, 2010 at 11:35 am in reply to: Amica cooker doors coming unstuck #332429
    SimonCD
    Participant

    Re: Amica cooker doors coming unstuck

    Thanks for your replies, I will look into the temp and wether they were left on if i hear any more from the customers.

    October 6, 2010 at 5:15 pm in reply to: Hotpoint WD440 no heat on wash #332213
    SimonCD
    Participant

    Re: Hotpoint WD440 no heat on wash

    The thermistor is prob out of range. Had one do this before.
    *edit sorry didnt read your post properly, i guess it would still go through prog if it were that!

  • Author
    Posts
Viewing 15 posts - 1 through 15 (of 119 total)
1 2 3 … 6 7 8