SimonCD

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 119 total)
1 2 3 4 … 6 7 8
  • Author
    Posts
  • May 28, 2010 at 12:37 pm in reply to: cda ci930 door handle #321271
    SimonCD
    Participant

    Re: cda ci930 door handle

    that was quick, thanks andy

    May 24, 2010 at 4:24 pm in reply to: “The drum just stopped!” :0 #320944
    SimonCD
    Participant

    Re: “The drum just stopped!” :0

    Yuck! i had a similar problem with a mouse in an old creda dryer fan once only the customer left it for a week before calling us. not nice…

    April 30, 2010 at 4:38 pm in reply to: Bosch Microwave Oven turntable runs when not in use. #319067
    SimonCD
    Participant

    Re: Bosch Microwave Oven turntable runs when not in use.

    I have had the same fault, the actuator that opens vent cover had shorted blowing a few tracks on main pcb. expensive!

    March 30, 2010 at 2:56 pm in reply to: hoover hnf7167 drum paddle fitting #316765
    SimonCD
    Participant

    Re: hoover hnf7167 drum paddle fitting

    Thanks Martin!

    March 17, 2010 at 6:42 pm in reply to: tdc32 water light glowing #315258
    SimonCD
    Participant

    Re: tdc32 water light glowing

    Damp float microswitch.

    March 17, 2010 at 6:39 pm in reply to: LG Bearing change advice #315314
    SimonCD
    Participant

    Re: LG Bearing change advice

    It is quite nice to work on. Motor off, tub out and split, pretty standard bearings too if i remember correctly.

    January 8, 2010 at 4:27 pm in reply to: AWO/D4505 #307909
    SimonCD
    Participant

    Re: AWO/D4505

    dont mention it

    January 6, 2010 at 8:34 pm in reply to: Miele Cylinder Cleaners #307793
    SimonCD
    Participant

    Re: Miele Cylinder Cleaners

    i believe you are correct they are wired differently, however the s512 probably just has a dry joint on the speed control pcb which i think is attatched to the motor casing. hope this helps.

    January 5, 2010 at 6:43 pm in reply to: AWO/D4505 #307906
    SimonCD
    Participant

    Re: AWO/D4505

    its resistor r020 on pcb. 0.5w 22 ohms.

    January 5, 2010 at 3:38 pm in reply to: Whirlpool awod 4505 fault code #307890
    SimonCD
    Participant

    Re: Whirlpool awod 4505 fault code

    thanks chezza, sadly its in a nice warm kitchen! i have also checked all components and insulation resistance so i guess is probably a pcb fault i would just like to be sure.

    December 18, 2009 at 6:13 pm in reply to: creda SO 77 EEX oven #306757
    SimonCD
    Participant

    Re: creda SO 77 EEX oven

    there is a tangential cooling fan at back under top cover, sounds like thats stuck?

    December 16, 2009 at 10:24 pm in reply to: Meile Novatronic Tumbledryer T260 tripping #306574
    SimonCD
    Participant

    Re: Meile Novatronic Tumbledryer T260 tripping

    Sounds like the heater but you will need to check insulation to be sure…

    December 1, 2009 at 7:11 pm in reply to: Flybe “airside” installs #302591
    SimonCD
    Participant

    Re: Flybe “airside” installs

    i had the pleasure of exeter prison, took every possible part with me for the dryer and it took 3 hours to get in and out!

    November 25, 2009 at 4:43 pm in reply to: Whirlpool awod4505 dead #304839
    SimonCD
    Participant

    Re: Whirlpool awod4505 dead

    ok, fixed it now, for future reference its r020 on pcb. 0.5w 22 ohms.

    November 17, 2009 at 9:20 pm in reply to: meggers #303345
    SimonCD
    Participant

    Re: meggers

    If its out anyway having just been fixed i turn off at spur switch and test from the supressor.

  • Author
    Posts
Viewing 15 posts - 31 through 45 (of 119 total)
1 2 3 4 … 6 7 8