timdowning

Forum Replies Created

Viewing 15 posts - 1,726 through 1,740 (of 2,180 total)
1 2 3 … 115 116 117 … 144 145 146
  • Author
    Posts
  • July 28, 2008 at 4:13 pm in reply to: BEKO WMB10W heater mounting? #258590
    timdowning
    Participant

    Re: BEKO WMB10W heater mounting?

    You might find the rubber seal is different? Shoulders on Beko no shoulders on WMA. Still if you seal it up and put a retaining clip on the heater to a mounting post somewhere that should stop it from popping out!!

    I find that shaping the spring from a servis door handle kit provides a good retainer. Or shaping the bracket that holds the drain hose in place on the back of hoover/candy machines another alternative.

    Peace of mind is a wonderful thing!!!

    July 28, 2008 at 4:05 pm in reply to: diplomat 8512 washer #258583
    timdowning
    Participant

    Re: diplomat 8512 washer

    Is this a Servis machine version???

    If so definitely the module. (Two large dropper resistors on the module).

    July 28, 2008 at 4:04 pm in reply to: BEKO WMB10W heater mounting? #258588
    timdowning
    Participant

    Re: BEKO WMB10W heater mounting?

    You could also try a shorter heater if you have one. Same idea as when the hoover logic range of machines lost their bracket. Electrolux heater 50681360009 worked a treat. (I think that was the part number.?)

    July 28, 2008 at 2:58 pm in reply to: Hotpoint WMA 66 Ultima #255057
    timdowning
    Participant

    Re: Hotpoint WMA 66 Ultima

    Got a WMA76 24124228 with no motor action.

    Rung out the wiring from motor to chopper board and chopper board to power module all ok. Motor is ringing out ok as well.
    There are no visual faults on the chopper board or power module.

    What do you think chopper board or power module at fault??

    July 22, 2008 at 2:15 pm in reply to: ISE Washing Machines #258198
    timdowning
    Participant

    Re: ISE Washing Machines

    ISE Admin: 0845 226 1268

    July 19, 2008 at 8:28 pm in reply to: They’re checking! #258038
    timdowning
    Participant

    Re: They’re checking!

    Anyone else had any similar experiences?

    Yes.

    After a tube of debor leaked in my van!!!!

    😀

    July 19, 2008 at 12:57 pm in reply to: ISE Dishwasher #257818
    timdowning
    Participant

    Re: ISE Dishwasher

    I didn’t want to be negative but I have to agree about the manual being ‘rubbish’. Luckily the dishwasher it replaced didn’t have a pre-wash and I didn’t sell it as having one. Shall have to wait and see if the customers reads up on it. hopefully not. 😉

    July 19, 2008 at 11:02 am in reply to: ISE Dishwasher #257815
    timdowning
    Participant

    Re: ISE Dishwasher

    Am I stupid??

    I’m sure the manual says there’s a prewash but programme dial dosen’t show one??

    Thanks.

    July 18, 2008 at 1:23 pm in reply to: ISE2 fault #257945
    timdowning
    Participant

    Re: ISE2 fault

    Could it be this???

    http://www.ukwhitegoods.co.uk/modules.php?name=Forums&file=viewtopic&t=35034

    Door interlock problem.

    July 15, 2008 at 3:11 pm in reply to: Hotpoint BWM12 19715153 #257763
    timdowning
    Participant

    Re: Hotpoint BWM12 19715153

    Thanks

    July 12, 2008 at 4:23 pm in reply to: closing down #221552
    timdowning
    Participant

    Re: closing down

    Drugs smugglings the future! 🙂

    July 11, 2008 at 2:42 pm in reply to: Is this washing machine any good?? #257056
    timdowning
    Participant

    Re: Is this washing machine any good??

    I decided on buying my last house quicker than what you’re taking over which washing machine to get. 🙂

    Just go for it.

    July 5, 2008 at 6:29 am in reply to: Hoover H160E – Wont start fast programs?? #257007
    timdowning
    Participant

    Re: Hoover H160E – Wont start fast programs??

    Had this a few times, change the timer/selector this should sort it!
    The part is only a tenner from Connect.

    July 2, 2008 at 5:48 am in reply to: Hotpoint WF321 #256381
    timdowning
    Participant

    Re: Hotpoint WF321

    Thanks

    July 1, 2008 at 5:05 pm in reply to: Hotpoint WF321 #256379
    timdowning
    Participant

    Re: Hotpoint WF321

    Thanks for info. Connect and Homespare have nothing listed for that part.
    What would the new merloni number be?

  • Author
    Posts
Viewing 15 posts - 1,726 through 1,740 (of 2,180 total)
1 2 3 … 115 116 117 … 144 145 146