admin

Forum Replies Created

Viewing 15 posts - 1,651 through 1,665 (of 12,518 total)
  • Author
    Posts
  • in reply to: GCG21YESBFSS wiring diagram #392992
    admin
    Keymaster

    Re: GCG21YESBFSS wiring diagram

    Hi

    Main PCB and Fan motor required. Simple

    We hold them in stock

    Bryan service@ffrservices.co.uk

    in reply to: new software for service/stock/data management #324682
    admin
    Keymaster

    Re: new software for service/stock/data management

    yes it has postcode mapping screen for route planning, very easy to use

    in reply to: basic fridge question #392932
    admin
    Keymaster

    Re: basic fridge question

    Hi

    The fridge door is separate from the fridge and dold no electrical components,the bush’s are plastic so in realistic terms there is no continuity between the appliance and door.

    Bryan

    in reply to: Which washer dryer? #392906
    admin
    Keymaster

    Re: Which washer dryer?

    i have supplied my Parents with the LG washer dryer and they are happy with it,
    I think they are good as far as washer dryers go

    in reply to: whitewestinghouse bi1200wd #392747
    admin
    Keymaster

    Re: whitewestinghouse bi1200wd

    It’s a Siltal machine,can be matched up with the CDA model.But they did change them mid production.

    Bryan

    admin
    Keymaster

    Re: What’s Recommended As Best Hob and Single Built-In Oven?

    Neff are good and so are Fisher & Paykel

    Simon

    in reply to: RSH1DBBP American Fridge freezer #392072
    admin
    Keymaster

    Re: RSH1DBBP American Fridge freezer

    unit will require new evap cover and possibly defrost parts behind it. only certain variations had a heater fitted. never had one fail though. look for incomplete defrost cycling.
    defrost sensor needs to be moved from r/h side of evap to suction line

    jr

    in reply to: General Electrical American Fridge Freezer #392524
    admin
    Keymaster

    Re: General Electrical American Fridge Freezer

    pipe is foamed in and non replaceable. jnr
    new door im afraid

    in reply to: Hoover HNL642 #392430
    admin
    Keymaster

    Re: Hoover HNL642

    thanks John

    in reply to: Teka dishwasher fault codes #391721
    admin
    Keymaster

    Re: Teka dishwasher fault codes

    any one 🙁

    in reply to: Hotpoint EW82S Top Oven Problem #391877
    admin
    Keymaster

    Re: Hotpoint EW82S Top Oven Problem

    Hi

    Switch the oven on for a minute or so with the trays ect removed, get a sponge or cloth onto the base of the oven and see if it heats and evaporates this is the most common element to fail,you an feel the heat from the top element by just putting your hand in the middle of the oven.

    If the water doesn’t evaporate or heat then it’ll be the base element or if the top one doesn’t then it’s the. Oven/grill element.

    Bryan

    admin
    Keymaster

    Re: Samsung RL41WGTB stops after few hours, requires power c

    Hi

    NO.. It’s time for you to contact SAMSUNG and advise that it’s a known defect. Changed piles of these whilst under warranty and it IS a manufacturers defect.

    Bryan

    in reply to: ise 1606 display dies #391851
    admin
    Keymaster

    Re: ise 1606 display dies

    And it was ?

    Bryan

    admin
    Keymaster

    Re: Samsung RL41WGTB stops after few hours, requires power c

    Hi

    You can’t. but they know there is one and i’ve got it somewhere..lol
    Can’ find it at the moment though.

    Bryan

    admin
    Keymaster

    Re: Samsung RL41WGTB stops after few hours, requires power c

    Hi

    the display shows the last held temperature. Also as there is a technical bulletin by samsung concerning the compressor fault and is known by samsung contact them to get ir replaced F.O.C.

    The original compressors used was MD4A1QL1U/E01 and then changed to MD4A1QL1U/E02 and in 2011 they started to use MD4A1Q1U/E03.

    Bryan

Viewing 15 posts - 1,651 through 1,665 (of 12,518 total)