Forum Replies Created
-
Posts
-
Re: Samsung RL41WGTB stops after few hours, requires power c
Hi
If its having to be left switched off for a while then it may be a faulty compressor which was fitted to this range about the age of yours. It would stop cooling but restart also if switched off and on again. This took ages and numerous wasted called to eventually find out. But I would be more prone to recheck the defrost side. The compressor will read correctly and will work once it cools down.
Bryan
Re: Guess what the ad is.
They used to be really good vacuums until they went into curry’s ect then went cheap and nasty.
Bryan
Re: new software for service/stock/data management
it does have lots of layers but the beauty is it can be as easy or complex as you want it to be, we are on the phone at least once a week asking Paul to change the system around for us, but even as a one man band it is an easy to use service and stock system.
Re: Mercury Range Respray
Hi Ken
If it’s in good condition then why not change the control panel at the same time then you can get them all the same colour,The sides are stainless anyway and all the fronts are available as separate parts as they are not complete doors but sections of doors.
Bryan
Re: Mercury Range Respray
Hi KK
The doors are enamelled so not just spray painted. Once removed they can be a pig to refit and align correctly also. How bad is the paintwork ?. You can order the outer skins also and as this cooker was approx 3K it would be worth spending a couple of hundred doing that the correct way rather than a botch up.
Bryan
Re: ISE 10 leak from soap drawer
If you try it out the dispenser with different flow rates you’ll get different results. And, the angle matters as well. I did that earlier today
Hi ken.
as the drawer cannot be removed whilst the machine is assembled on the new model how is it possible to measure the flow rate ?. And what is the flow rate required as on a normal drawer it is possible to remove the drawer and watch the water flow from each jet.
I still say it is something to do with the syphon design that has been changed from the previous model which has the same shape drawer but a pull out one.
The drawer stand up pipe syphon is lower on the previous model and is below the drawer lip by about 2-3mm which would allow the syphon to start before the water overflows the lip of the dispenser drawer.
the stand up syphon pipe in the new drawer stands proud above the drawer lip by about 3mm which means the water has to fully fill with probably faster water pressure to get the syphon to activate as the section over fills before the syphon activates and can continue.
Bryan
Re: ISE 10 leak from soap drawer
I’ve just tried the same with a drawer I changed a few months back. I found that the liquid detergent side did not start siphoning straight away and the water leaked out into the comfort section (which did syphon), and also around the edge of the drawer under the plastic cover. This could also be causing the leak at the drawer front.
Thank god i’m not the only one..thought I was going mad,Have you solved the problem ? alan ?
Bryan
Re: ISE 10 leak from soap drawer
Hi Ken
I have as said before tried the dispenser with JUST water so the design of the syphon part seems to have changed. The syphon normally sits below the top level of the drawer but on this new one its slightly higher than the back of the drawer which means it will go over the back edge and take more effort to start the syphon effect. I have tried it over a sink and have to jog the dispenser to get it to start.
Bryan
Re: ISE 10 leak from soap drawer
We also have a problem with a dispenser not taking the liquid detergent away from the liquid section. Have also tried with the whole dispenser out under a tap and it still doesn’t start siphoning straight away unless its moved.
New dispenser fitted,water adjusted but still to flushing away.
Bryan
Re: Whats the most annoying thing customers do?
regards last two posts, i find that most the people that phone you at weekends to be a waste of time , so i dont bother with them,
i just wait till monday till i pick up the phone again , i enjoy my weekends,with out theses types of callsRe: dryer fire on bbc news this morning
hotpoint dryer burt garage down last year fluff,not cleaned out
was in garage thankfully,Re: Skim Words
Hi Ken
Is these the highlighted words like in the Beko T/D thread ie Meile ect in dill’s last comment ?
Bryan
Re: dryer fire on bbc news this morning
Nope mod fits another plastic cap.
Got the bulletin sheet issued from Beko
Bryan
Re: dryer fire on bbc news this morning
bbc report here:
http://www.bbc.co.uk/news/business-21630150
oops misssed the link on the bottom of the first post,
