Forum Replies Created
-
Posts
-
Thanks guys the door was defo knackered I hope that my new machine will last more than 2 years anyway thanks foe your help
Re: ariston magerta 2000a
Thanks my husband has busted the door I have alredy been looking online for a new machine I have 3 kids so this is the last thing that I need espically on Motheers Day!!!!
Re: AEG Error MSG C3 on model oko_favorit 50700
Hi and many thanks for your advice. Will try this now and I think this could work as we found just tilting it slightly and back again cleared the error (we did get some water out but obviously not enough to drian it fully!) As soon as we moved the machine slightly afterwards, the fault came back again. Will let you know.
ThanksRe: AEG Error MSG C3 on model oko_favorit 50700
Forgot to say – make sure you switch off & unplug first!
Re: AEG Error MSG C3 on model oko_favorit 50700
Heres something you could try:
Pull the machine right out into the room
Looking from front, lay a couple of towels along the underneath of the left side panel
Gently tilt the machine to the left side – dont put it right down on its side just tilt it a few degrees – if there is any water in the base it should now be running out onto the towel.
Do not be tempted to tilt the machine backwards – if there is water in the base it will run straight into the mains terminal block.
Once you have drained enough water the float will automatically reset & you should be able to run the machine.
If the machine keeps stopping with C3 then you have a leak somewhere – get someone out to have a look, dont be tempted to start trying to by parts yourself unless your dead sure whats wrong as parts for these dont come cheap!Re: First Kitchen First Everything
Hi Senga
Firstly for the range cooker I personally would choose a Mercury range cooker,they are hand built in the UK,slightly more expensive but well worth it and also available in different colours.http://www.mercury-appliances.co.uk/quality.asp
as for the built in range of refrigeration,I would get an appliance that had the lease amount of electronics on it preferably standard if possible as the electronics may be reliable but when they do go wrong then the pcb’s are normally expensive.
As for the dishwasher there wont really be much to choose from as most of the slimlines are made by a few manufacturers badged into different names.
hope this helps
bryan
Re: AEG Error MSG C3 on model oko_favorit 50700
Forgot to say, I’m happy to remove panel if you think I will be able to achieve anything
Re: AEG Error MSG C3 on model oko_favorit 50700
Thanks for info. Any idea on costs of circuit board if gone? 🙂
Re: neff u1420w0gb/02 oven door handle broken
Thanks for advice.
Had to cut the glass away from the seals in the end by sliding knife around flat to the glass. Now have separated the pieces and installed the handle. Will have to order new seal strips from bsh.
Thanks again.Re: AEG Error MSG C3 on model oko_favorit 50700
Thanks for help. Have cleaned everything out today but no blockage and washing machine plumbed into dual water outlet all works fine. Still got C3 error message showing. Can I locate the float or is this not visible ?
If it sounds like the sensor board or float needs replacing, do you know if this is cost effective or best to spend towards a new machine?Re: Zanussi Fridge Freezer defrosting on freezer
Hoggy, if the freezer evaporator is not cold & fridge is ok then you most likely have a small leak somewhere. If you leave it then eventually the fridge will probably fail as well. If you’ve got a DF62/21FF then it must be over 12 years old by now and will be charged with R12 – a cfc gas so check around with your local engineers, some wont touch it, others will regas with a “drop in” replacement but unless the cause of the leak can be found youre wasting your time and your money. You need to weigh up the cost of regassing against how much longer this thing will realisticly last.
