[admin]

Re: Bosch 6312 Dishwasher: No Heat

pms wrote:Thanks once again . I’ll give them a try. Incidentally , tried a bosch service and they wanted £59 + vat for the first half hour! A complete joke.

Best wishes

Peter

It’s £59.50 INC VAT. We do not resolder this heater relay back up as it’s seen as a temporary repair :duck:

[admin]

Re: AEG Error MSG C3 on model oko_favorit 50700

just a quick question and forgive my little expertise, the tray inside seems empty, so do I need to take machine apart to get to this or just look underneath or from the back?
When I plug machine in, the pump turns on. If I select a program, it starts for a few seconds and then switches back to error message.
Thanks again

[admin]

Re: AEG Error MSG C3 on model oko_favorit 50700

Thanks for for the info and will give it a try. The pump seems to be working constantly while plugged in, so hopefully its just the water in the tray. will let you know. Most kind.

[admin]

Re: New World Series II gas cooker – door seals?

And lookng further into the service manual, I’ve found that the door seal I need is Part No 162461900, G C No 021 588.

Obsolete, probably?

Ed

[admin]

Re: New World Series II gas cooker – door seals?

I had rather hoped that someone would say I could march into a supplier’s and ask for three metres of Type 42 ….. !

Silly, of me, I know.

Maybe I should just have followed my first instinct, which was to take a short length of the disintegrating rubber into a spares shop and say; “Hey, ya got any of THIS?!”.

[admin]

Re: ariston LSI 61

It sounds like the controller is in ‘lock out’ mode.

If an error occurs (eg Flood sensor activated) the controller ‘locks out’ to prevent further operation. Normally you’d need an engineer to repair the fault and reset the controller.

There are instructions to reset the controller here and a few tips on LSI61 dishwasher repair:

http://www.geocities.com/davehills/ariston

[admin]

Re: New World Series II gas cooker – door seals?

OK, the GC Appliance No is 11.645.26 (White).

Looking at the manuals (yes, I’m that sad – I have the original manuals from ….. er, 1987, it says!), these ovens used to be described as ‘slide under’, rather than built under.

[admin]

Re: Suk90mfx – not heating properly in Fan Mode

Thanks for your replies guys.
Sorry I forgot to mention it was a 90cm Smeg Dual Fuel.
I’m surprised to find SMEG so unreliable, and their customer service very poor.

I’m a competent DIY’er, but do I need a professional to handle such a job?

Also, Could I buy the elements from this site?

Regards C

[admin]

Re: Diplomat Select 610 Oven Door Seal

I have finally got it… the make and model no that is, for my door seal

Its as you described Penguin 45..

Make DIPLOMAT ( MFI Manufacturing Howden DN14 7PA)
MODEL: AHY 3300
SERIAL No. : 01137023

Many thanks in advance….

Mike

[admin]

Re: Integrated Larder Fridge APM 6315, 6115,6215

eddy0 wrote:I have an integrated fridge that the hinge has snapped on. Could you help me source a spare. I do not know the manufacturer and only have a booklet with the following codes on.
APM 6315/6321/6325
APM 6115/6121/6125
APM 6215/6221/6225
Thanks

Dave, I have exactly the same problem with my fridge as well and it is the same make as above. The problem hinge is the right/top fitting. How can I order a new one from you please?

Thanks

Liam

[admin]

Re: Sven oven

the fault then will be the potentiometer that is within the hob unit that is connected by an umbilicle lead to the oven assembly.

the hob will have to come out to effect the repair and hopefully the installer has fitted it with a cooker hose(makes life a lot easier) 🙁

once the hob is out remove 2 screws on each side ond the glass top will come off.

once inside the potentiometer is in a case in the center front of the hob and the cover is secured by 2 phillips on the base of the hob,you will need to unsolder the old one one solder the new one ( only 3 wires though ).

re assemble and there you go.

give me a call for the potentiometer 07961365484

bryan

[admin]

Re: Iceline Frost free not frost free !!!

I very much doubt that there will be a diagram for this appliance as there is really only a PCB,fan,heater,overload,defrost sensor and the compressor that is replaceable and any engineer that knows refrigeration shouldnt need a wiring diagram for this model as the pcb isnt repairable by an unspecialised company.

bryan

[admin]

Re: worldco / Teba

I personally think for the cost of the product it was a good unit,yes there was niggly faults but at least the parts was standard through out the range basicly.

Yes there was problems with spares but dont all manufactures have the same problem at some points.and at least ifit did break down the cost of parts didnt write off the appliance unlike several manufacturers.

Most of the problems came from customers wanting a smeg/bosch quality cooker for the cost of £150,It does come down to you get what you pay for and dont have massive over expectations.

I am sad to see the product go but will continue to hold stock of parts and service the product that is still out there.

bryan

[admin]

Re: Sven oven

Yep

What’s the fault you have got? and I’ll tell you what the part is you’ll need.

I carry all the spares in stock for these ovens.

tel 07961365484

bryan

[admin]

Re: Iceline Frost free not frost free !!!

hi,

You will need to post model number and serial number to find more help.

The system engineer will not need a diagram, otherwise he ain’t a system engineer, so is it a wiring Diagram you are after?

Kevin

[Author]

Posts