[admin]

Re: Use Of Funds

Agree, seems only thing to do if we are to stand on our own feet

ted

[admin]

Re: Whirlpool adp5966 dishwaher F3 error

Hi,

F3………1) Heats the water too slowly.
2) No heat
usually takes 29 minutes to fault to F3

I think this dishwasher is the optical sensor one which means any of these can be faulty.

Sensor…4812 271 28459 Could just want cleaning(the lens surface gets grubby)

heater(tube type) 4812 259 28684 Check resistance and insulation

base control card…….481221478704 .. inspect for edge connections and blown tracs on the board(indicating failure elsewhere in the dishwaser)

even if you are extremely confident in your abilities I would recommend you get an experienced engineer to this, it could well save you money because wont need all three parts.

ted

[admin]

Re: Compensation for Damaged Feelings

It just so happens that MAYTAG are one of the companies with a cheque book open and ready to write cheques for damaged feelings,In fact if you complain enough they will write enough cheques to cover the cost of the appliance…in one instance the customer said after a repair” this isnt going to happen again is it ” the answer dont be silly or daft its a one off it doesnt normally happen (tongue in cheek,lying through your back teeth as you go to at least 2 a week).

For this a customer receives a cheque for £100.00.

as it happens now..question:-do you get many of these ? answer as honest as possible: ive done 6 already this week madam and its only tuesday. 😈

Bryan

[admin]

Re: Can I get Stainless Handle/Knobs for Whirlpool ADG332

Sorted thanks Ted, Dave has sorted me out with the bits. Should be arriving in the post any time!

David

[admin]

Re: R600A to be banned!

And I thought what the ${e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d}&* have i done now…….

Bryan 👿

[admin]

Re: Can I get Stainless Handle/Knobs for Whirlpool ADG332

hi,

if you are able to view this appliance in your local store then obtain the 12 nc number from the appliance.

With this number I can order the parts you require and delivery is usually 4 days from Italy.

If the parts are incorrect I will accept them back as long as you accept the postage to return to me and they arrive in saleable condition.

The 12 nc number is located on a lable on the inner edge of the door usually left hand side

regards

Ted

[admin]

Re: Can I get Stainless Handle/Knobs for Whirlpool ADG332

I understand that totally, the car spares market is the same with exploded line art diagrams of parts in black and white PDF’s.

My issue is, this dishwasher (as far as I remember) was available in white, brown and Stainless, – white being denoted by WH at the end of the Model Number.

Surely then if I quote ADG332SS instead of ADG332WH then I will get the right parts for the Stainless version?

This shouldn’t be this difficult 🙁

Thanks

David
ps it looks like this

[admin]

Re: Teba/gunkol built-in oven. Manual required. Model A02004

Teba have a HELP LINE number that customers can use for this sort of enquiry.

0870 2401916

This is facilitated by D&G.

Richard

[admin]

Re: Grinding and bumping

Diplomat 8702 Washer Dryer
Sorry I thought I was working in a specific forum area dealing with this particular machine. Querry is still as before. How do I remove the bearing set from the rear of the drum so that I can replace them. Thanks

[admin]

Re: Power Board for a Smeg SUK91mfx

Power board implies an electronic control type of appliance.
Im not familiar with Smeg appliances to such a degree but this sounds like you should be careful.

Consider firstly why its a bargin……blown power board..WHY did it blow.

Smeg spares are hardly reasonably priced

There are several of our members who do Smeg repairs

You always get what you pay for and buying a broken appliance seems like the wrong move to me

all the best in whatever you decide

ted

[admin]

Re: appboy

hiya mate, glad your back and i dont retract a word.

If the cap(knickers) fit……….

ted

[admin]

I understand Appboy is very good at undercover work.

Mind you dont give him anything to look after as he loose things!

[admin]

That would be a good idea Del, orginally Connect where to distribute orbit for Dasa on the understanding they could send fliers with it. I m sure if we asked they would jump at the chance.

Go for it .

[admin]

Re: HOMARK SPARES

depending on how old this unit is it may be a model made by SERVIS or lately ARI SILTAL by the looks of the ones ive seen lately though EAC.
If is AI SILTAL then ive got a motor in stock.

Bryan

[admin]

Re: Subscribers forum

and i must do mine tomorrow, sorry guys

[Author]

Posts