allan

Forum Replies Created

Viewing 15 posts - 106 through 120 (of 200 total)
1 2 3 … 7 8 9 … 12 13 14
  • Author
    Posts
  • July 14, 2010 at 4:12 pm in reply to: AEG bearing kit #325301
    allan
    Participant

    Re: AEG bearing kit

    Thanks for that 🙂

    July 10, 2010 at 6:45 pm in reply to: Tricity /Bendix sie532bu #325068
    allan
    Participant

    Re: Tricity /Bendix sie532bu

    Thanks Dave:)

    May 6, 2010 at 9:10 am in reply to: White knight wk100.2 bits #319489
    allan
    Participant

    Re: White knight wk100.2 bits

    Thanks Chris 🙂

    April 23, 2010 at 8:08 am in reply to: Wiring loom for candy cn100? #318565
    allan
    Participant

    Re: Wiring loom for candy cn100?

    Thanks Martin, tried connect their showing it as obsolete! any ideas?
    Thanks

    April 20, 2010 at 11:17 am in reply to: Hotpoint wd420 mains filter/ harness #318288
    allan
    Participant

    Re: Hotpoint wd420 mains filter/ harness

    Just finished job, had five wires from mains filter L, N, 2 earth G/Y at back and a black wire in between L and N which is also earth on mains filter, got them out of old harnes and refitted to new one all seem ok.

    March 12, 2010 at 8:54 pm in reply to: Whirlpool AKZ457/1x/01 fan element #314848
    allan
    Participant

    Re: Whirlpool AKZ457/1x/01 fan element

    Thanks Chris 😀

    March 12, 2010 at 7:24 pm in reply to: wma33 door light flashing #314846
    allan
    Participant

    Re: wma33 door light flashing

    Yes will do, thanks for the reply
    Allan

    March 11, 2010 at 1:06 pm in reply to: hotpoint wd420 dead #314596
    allan
    Participant

    Re: hotpoint wd420 dead

    Yeah checked them, both okay, read a thread with similar prob, someone advised to check motor brushes? would that not have thrown up a fault code/
    thanks

    February 10, 2010 at 8:13 pm in reply to: firenzi oven F03 #311615
    allan
    Participant

    Re: firenzi oven F03

    Thanks again Chris 🙂

    February 8, 2010 at 7:43 pm in reply to: hotpoint wf 100 F08 fault #310984
    allan
    Participant

    Re: hotpoint wf 100 F08 fault

    No tried new pressure switch, Checked every wire from start to finish and all connectors, spoke to qer reckons they test thoroughly and would not be the board……………but?

    February 4, 2010 at 10:03 pm in reply to: hotpoint wf 100 F08 fault #310980
    allan
    Participant

    Re: hotpoint wf 100 F08 fault

    is it possible qer has overlooked something?

    August 24, 2009 at 1:14 pm in reply to: Beko wm5120w module? #295308
    allan
    Participant

    Re: Beko wm5120w module?

    Thanks will check that before ordering, and thanks for the part no. 🙂

    June 29, 2009 at 8:59 pm in reply to: Firenzi oven element #290586
    allan
    Participant

    Re: Firenzi oven element

    Thanks yet again 😀

    June 29, 2009 at 12:00 pm in reply to: Hoover Nextra board? #290524
    allan
    Participant

    Re: Hoover Nextra board?

    Hi Martin and thanks for the mail, goes through the cycle but no heat, no flashing fault codes either?
    allan@cherrytree.adsl24.co.uk
    Thanks

    May 26, 2009 at 6:52 pm in reply to: soft start for vacuum cleaner #287875
    allan
    Participant

    Re: soft start for vacuum cleaner

    no modern day z410a, the part is an ntc apparantly, but where it is burned cant see numbers it should be a common part, its just knowing which values to go for from the chart that i have linked

  • Author
    Posts
Viewing 15 posts - 106 through 120 (of 200 total)
1 2 3 … 7 8 9 … 12 13 14