bazza500

Forum Replies Created

Viewing 15 posts - 451 through 465 (of 1,916 total)
1 2 3 … 30 31 32 … 126 127 128
  • Author
    Posts
  • January 20, 2012 at 2:14 pm in reply to: BUSH APPLIANCES #367546
    bazza500
    Participant

    Re: BUSH APPLIANCES

    Can sometimes tell from the serial number if you have that.

    January 17, 2012 at 8:37 am in reply to: Pre Feb Mtg 2012 #364883
    bazza500
    Participant

    Re: Pre Feb Mtg 2012

    The folders should be all finished by then. I will bring them with me. What “welcome letter” is going in them?


    Val will do as little or as much as you need her to (she said).

    January 16, 2012 at 11:36 pm in reply to: Swan Appliances gone bust? #367004
    bazza500
    Participant

    Re: Swan Appliances gone bust?

    All the ones I’ve seen are Vestel.

    January 15, 2012 at 10:11 pm in reply to: BEKO no go! #367314
    bazza500
    Participant

    Re: BEKO no go!

    I sometimes give it a blast with compressed air but most of the time it doesn’t require anything.

    January 15, 2012 at 9:28 pm in reply to: BEKO no go! #367312
    bazza500
    Participant

    Re: BEKO no go!

    Compare them to your new ones before you fit them. Paying particular attention to the slope on the face of the brush. Some of the copies the slope is too much and causes only the tip of the brush to contact the motor causing overheating. This then results in the motor needing replaced.

    January 15, 2012 at 8:46 pm in reply to: BEKO no go! #367310
    bazza500
    Participant

    Re: BEKO no go!

    I would watch with the non gen Beko brushes. I stopped using them as they were causing excessive arcing and blowing the motor toc’s.

    January 15, 2012 at 8:23 pm in reply to: BEKO no go! #367308
    bazza500
    Participant

    Re: BEKO no go!

    Yes, they are the correct ones for your machine.

    January 15, 2012 at 8:01 pm in reply to: BEKO no go! #367306
    bazza500
    Participant

    Re: BEKO no go!

    madrat wrote:

    I tried moving it by hand when I started the program but it still wouldnt go.

    The last person I knew of who did that lost 3 fingers. :eeek:

    January 15, 2012 at 7:39 pm in reply to: BEKO no go! #367301
    bazza500
    Participant

    Re: BEKO no go!

    Brushes?

    January 12, 2012 at 7:12 pm in reply to: Bush A126Q washing machine door seal #367104
    bazza500
    Participant

    Re: Bush A126Q washing machine door seal

    Also available from Connect and probably easier to get.

    January 5, 2012 at 7:42 pm in reply to: Electrolux EOB5630X thermal cut-out fan motor wiring advice #366629
    bazza500
    Participant

    Re: Electrolux EOB5630X thermal cut-out fan motor wiring adv

    Sorry Pedro but forum rule No.8 applies

    cooker-oven-forum/professional-advice-the-public-forums-t4361.html

    January 5, 2012 at 6:57 pm in reply to: Beko DRVS73W tumble dryer vented #366666
    bazza500
    Participant

    Re: Beko DRVS73W tumble dryer vented

    2958000300

    January 1, 2012 at 9:43 pm in reply to: Pre Feb Mtg 2012 #364871
    bazza500
    Participant

    Pre Feb Mtg 2012

    I can do the 20th

    December 31, 2011 at 9:01 am in reply to: Russell Hobbs Washing Machine £160 #366099
    bazza500
    Participant

    Re: Russell Hobbs Washing Machine £160

    peterjay wrote: no parts or tech has been supplied so if they go wrong asda will replace

    Incorrect. Service done through JTM.

    December 27, 2011 at 10:10 pm in reply to: Miele T490 #366028
    bazza500
    Participant

    Re: Miele T490

    bazza500 wrote:Having read a few posts on this forum it would seem that the carbons being worn and jumping off the nut would cause it not to heat. Is this right?


    … and is there an easy way to get the belt back on?

    Anyone know the answers to these questions?

  • Author
    Posts
Viewing 15 posts - 451 through 465 (of 1,916 total)
1 2 3 … 30 31 32 … 126 127 128