Beever

Forum Replies Created

Viewing 15 posts - 31 through 45 (of 114 total)
  • Author
    Posts
  • in reply to: The One Show #358602
    Beever
    Participant

    Re: The One Show

    Dom littlewood is a reformed theif. He used to rob houses for a living!

    in reply to: Bosch dishwasher pcb triac failure #358947
    Beever
    Participant

    Re: Bosch dishwasher pcb triac failure

    Replace the soap despenser!

    in reply to: Neff combi H7871 GB #340573
    Beever
    Participant

    Re: Neff combi H7871 GB

    also check the light bulb, they can cause serious damage on the early machines.
    The newer versions have a big green resistor in the lighting curcuit to prevent the bulb taking out the PCB’s

    in reply to: NEFF ERROR CODES #338821
    Beever
    Participant

    Re: NEFF ERROR CODES

    I think from memmory its the PT500 sensor
    Part no:- 175710.
    Hope it helps, its been a long time!

    Regards

    Ian

    in reply to: Bosch WAE24162 can the fault code be cleared? #338823
    Beever
    Participant

    Re: Bosch WAE24162 can the fault code be cleared?

    suspect the motor or PCB is knackered, as you shouldnt have to clear a fault for the machine to work.

    Regards

    Ian

    in reply to: AEG 60870 PNC 911 232 542 04 #338856
    Beever
    Participant

    Re: AEG 60870 PNC 911 232 542 04

    Usually a not draining quickley enough fault!
    Check the usual, IE Plumbing spout, kinked hose, filters, pressure switch hose/ switch.

    Ian

    in reply to: Neff oven fan motors tripping electric. Just a note #338850
    Beever
    Participant

    Re: Neff oven fan motors tripping electric. Just a note

    After 10 1/2 years for BSH and 20 years in the trade, I can honestly say I cannot ever remember changing a fan motor for tripping the electrics. I have changed tons for seized motors for fan blades stuck on the fan shaft but not for tripping?

    I wonder if it may have been a coincidence.

    Kind regards

    Ian
    😕

    in reply to: bosch #338772
    Beever
    Participant

    Re: bosch

    superfix wrote:

    raw wrote:
    very easy strip knock bearings out fit new ones rebuild half hour job sorted 😀

    You’re havin a laff.. It’s a tank out and split it job

    LOL @ half hour job sorted. WFF, WFP V4380X0GB machines at a push! not any of the WFL, WFO, WAA or WAE 30mins just to get the full tank out!!

    in reply to: Best make of van for the job (all rounder) #337713
    Beever
    Participant

    Re: Best make of van for the job (all rounder)

    Ally, I love my VW t5 4motion. It has the 4 wheel drive ur after, air conditioning, heated seats, electric windows and mirrors, mirrors are heated too. It is also fitted with the winter pack, so has heated washer bottle, heated jets and headlight washers, so no more frozen jets or frozen washer bottle. Plus loads of other bits n bobs.

    A bit on the expensive side to buy new, but the way I see it, you get the vat back and it’s a van that’s going to give loyal service for many years. Think I will keep mine until it’s dies!

    Regards

    Ian.

    in reply to: Best make of van for the job (all rounder) #337707
    Beever
    Participant

    Re: Best make of van for the job (all rounder)

    SAMURI wrote:I have a Ford Transit Sport it is like a car to drive It has a heated windscreen, heated leather seat, electric windows and mirrors, electronic stability program, traction control, cruse control, low profile alloy wheels and tyres 6 disc radio cd player etc etc. Downside is the cost of tyres and low mileage out of tyres.

    It still would not be as good as your van in the snow, but is still good compaired to your 4 x 4.

    I have a 4 x 4 as back up for snow.

    Ford now do a 4 X 4 Transit not as good a drive as the sport but still a nice van.

    Sounds like home from home!!

    in reply to: Best make of van for the job (all rounder) #337705
    Beever
    Participant

    Re: Best make of van for the job (all rounder)

    I have had vauxhall combo’s new shap and old & had a high top LWB 2800, that was when we had the shop and those 6″2 Bosch kgu’s to deliver. All the vauxhalls I had were fab. As we cover the Bolton abbey estate for the duke, the vivaro used to be a bit rubbish in the bridal paths and farm tracks. The 4motion is top!! It’s a wee bit on the thirty side @27 mpg! Lol. Mind it keeps my tax bill down!!

    in reply to: Bosch WFP3300 Fault code F07 #335208
    Beever
    Participant

    Re: Bosch WFP3300 Fault code F07

    Glad to have been able to help!

    Ps don’t part with that machine ever, it’s one of the best machines Bosch have ever made, and most likely ever will make!
    🙂

    in reply to: Miele T494C #336267
    Beever
    Participant

    Re: Miele T494C

    Cheers big ears!

    £46.00 robbing gets!

    in reply to: beko d/w #336250
    Beever
    Participant

    Re: beko d/w

    its the little wax actuator on the dispenser?

    in reply to: Bosch WFP3300 Fault code F07 #335206
    Beever
    Participant

    Re: Bosch WFP3300 Fault code F07

    F07 is the NTC o/c. also check the 2 brown wires all the way back to the PCB!

Viewing 15 posts - 31 through 45 (of 114 total)