[Beever]

Re: Neff 296271 Element

part no 296271 grill. Still available!!

[Beever]

Re: Regassing tumble dryers

I have been to three of these appliances, 2 with the cooling fan @ the bottom front coming loose causing fan to jam/ be noisy and one with fan fitted in reverse, sucking instead of blowing!

Very clever in principal, takes an age to dry.

Basically, the condenser is refrigerated and the waste heat from the comp is channeled into the drum to dry the laundry!

Brilliant! A+ energy rating (a fridge that dries your washing)

[Beever]

Re: Bosch D/W SGS43E08GB (S9G1B) strip down

they are the plastic base dishwashers with the mushroom float!

[Beever]

Re: AEG Santo F/F model 75388kg

freezer NTC Kit

[Beever]

Re: leisure cooker

Need the full model number to look up the diagram fro you!

[Beever]

Re: AEG F/F S75348KG

The PNC Number is needed in order to help you!

[Beever]

Re: Bosch D/W SGS43E08GB (S9G1B) strip down

LOL well done superfix!! I think they must like to make a very easy job into somthing more difficult. You can change a wash pump on a freestending dishwasher in less than 25mins, start to finish. Why mess around taking the base off?

[Beever]

Re: Miele washing machine dead

Check the door lock plug, had a number of them becoming disconnected for no apparent reason! Re fit it and secure with a cable tie.

[Beever]

Re: Bosch wfb2000 no mt problem

I assume you have a WFF2000 Not a WFB2000. WFB is a very basic appliance with no fault indicators. Have you checked the drain spiggot under the sink to see if a button or 5p is acting like a butterfly valve?

[Beever]

Re: NEFF CERAMIC HOB

Hmmm Induction Hob!! Usually Module 438661(Rhs) £216.79 444400 (Lhs) £197.74 not too uncommon, usually the vents or the intake fans have been blocked. Check the install.

[Beever]

Re: Bosch SGS53A0GB/27

The ENR Number is not correct!
If the ENR is SGS53A02GB/27 Then yes 482935 is the correct module.
Regards

Ian B

[Beever]

Re: I’ve found it!!!!!!!!!

HVR700878 element:Upper-fan (Grill ele H7292)
SRP: £194.89
Order Code: 5031680688450

Grill Element Costs More Than The Oven LOL

[Beever]

Re: Beko WMA1715S

I Belive that prewash light flashing only indicates that the machine has gone into fault, and is not the fault code indicator. To find the fault code indicator you have enter the after sales test prog to display the last stored fault!

Hope this helps.

[Beever]

Re: Known Test Procedures

Beko WMA765S

Flash Functional Test Program
Entrance to the test mode:
1. Turn off the machine from On/Off Button
2. Turn on the W/M from the main switch, while pressing “start/pause/cancel” button and the selected program is cotton
90. Start icon will start to blink within 3 seconds. At the moment, you can see the code of failure in follower LEDs or on 7
segment.
3. After seeing the failure, erase the failure by pressing start/pause/cancel button 3 seconds without losing any time
4. After erasing the failure code, you will be in functional test mode. Each push to the start / pause / cancel button will
represent one function.
Functional Test Sequence:
1. All LEDs on the board will start to blink after the door is locked.
2. Take in water from pre-wash compartment
3. Take in water from main wash compartment
4. Take in water from softener compartment
5. Take in water from main wash compartment if the W/M has a hot valve option (If not this step will be skipped)
6. The heater will be ON. If the water level inside the tub is not enough for the heater to switch on then all valves will be
turn on to fill the level.
7. Clockwise motor rotation with 52 rpm
8. Counterclockwise motor rotation with 52 rpm
9. Draining
10.Spinning up to maximum speed.
11. Turn on all the valves to fill a certain level in a short time for water leakage test on the production line.
12. End
13. You can get off the test mode by turning the WM off.

Faults:-

H1 : NTC OPEN CIRCUIT OR SHORT CIRCUIT ( 10000 )
H2 : HEATER OPEN CIRCUIT ( 01000 )
H3 : HEATER ALWAYS ON ( 11000 )
H4 : VALVE TRIAC SHORT CIRCUIT ( 00100 )
H5 : PUMP OPEN CIRCUIT ( 10100 )
H6 : MOTOR TRIAC SHORT CIRCUIT ( 01100 )
H7 : PRESSURE SENSOR FAILURE ( 11100 )
H11 : MOTOR / TACHO OPEN CIRCUIT ( 00110 )

Help:-

Not able to select any program ( As warning softener led blinks in program follower ) IF Yes:- Check program selector resistance and compare
the value with the table:-

1. Position ~1 Kohm
2. Position ~2 Kohm
3. Position ~3 Kohm
4. Position ~ 4Kohm
5. Position ~ 5Kohm
6. Position ~6 Kohm
7. Position ~7 Kohm
8. Position ~8 Kohm
9. Position ~9 Kohm
10. Position ~10 Kohm
11. Position ~11 Kohm
12. Position ~12 Kohm
13. Position ~13 Kohm
14. Position ~14 Kohm
15. Position ~15 Kohm
16. Position 16 Kohm
If All the resistance values ok:- Check connection between program selector and main board. If there is not a problem at connection change the Main PCB.
program selector and main board.

If All the resistance values are not ok:- Change the program selector

Is RINSE led blinking in the program follower ? If Yes:- Check Valves/ Voltage to valves/ Water supply to valves.

Is MAINWASH led blinking in the program follower? If Yes:- While programming card, an error may have occurred in one of the processing stages,
change the Main PCB.)

[Beever]

Re: Bosch wok2001gb/05 Bearings

you don’t need to take it out ??

[Author]

Posts