[Beever]

Re: Bosch washer dryer fault code?

water inlet time too long, check valves, pipes taps, strainers

[Beever]

Re: Bosch DKE995AGB hood – no lights!!

4.0A Fuse on pcb part no:- 705194

[Beever]

Re: Whirlpool Side By Side

Serial No:- 110410022546

Cheers

[Beever]

Re: Bosch WFO2864 washer aborting pgm after 2 mins.

The End / Ready light, in fault display mode indicates that the door is open after programme has started. From experience, this is usually the pcb. Part No:- 445554 £102.30 inc vat.

[Beever]

Re: Whirlpool Side By Side

Thanx Rob u r a star!!

[Beever]

Re: Whirlpool Side By Side

Hmmm i dont see that part listed on Sios for this appliance, is that deffo the correct part no for this model. Oh and do you know if you have to change both pcb’s together? This appliance is fully defrosted, when it is switched on the alarm sounds, after about 40 seconds the heat exchanger fan starts, but no live to the comp. If i supply a live feed, comp starts and runs fine and appliance starts to cool. Is it possible that it is just the bimetal sensor that is faulty and not the pcb?
strange one!

[Beever]

Re: Bosch Dishwasher keeps filling

There is a modified mushroom float and pcb for the older plastic bottom dishwashers! The new version of the plastic bottom dishwasher has no magnetic float fitted.

[Beever]

Re: NEFF COOKER

Is ther a welded / stuck/ blown contact on the selector switch ?
😳

[Beever]

Re: Bosch WTA3204GB/09

this appliance is an auto sensing one. if there is no wet load in the appliance, it will switch off within aprox 2 mins. It passes a current through the laundry, this charge is then picked up between the tank and the paddles, the drum and the paddles can get coated with a coating of softener, give the tub and paddles a clean to ensure that the charge is being detected.

[Beever]

Re: Bosch WTA3204GB/09

Check the heater ntc on the heater

[Beever]

Re: BOSCH LOGIXX DISHWASHER SGS66A02GB/17 STRANGE FAULT

hmmmm, must have been having a bad day, sorry! 😳

[Beever]

Re: Known Error Codes

MIELE

F1 NTC sensor short-circuited water / heating
F2 NTC sensor open-circuited water / heating
F3 NTC sensor short-circuited air path / fan
F4 NTC sensor open-circuited air path / fan
F5 Oven Pt 1000 sensor short-circuited
F6 Oven Pt 1000 sensor open-circuited
F7 Catalyser Pt 1000 sensor open-circuited
F8 NTC sensor fault – General
F9 Vacant
F10 Water intake
F11 Water drainage
F12 Water intake fault at start of step
F13 Water intake fault at end of step
F14 Water intake fault – Level switch – Heating
F15 Water intake fault – Hot water
F16 Foam / Excess detergent
F17 Insufficient water intake
F18 Flow meter stationary
F19 Flow meter slow / difficult to rotate
F20 Heating
F21 Grill heater element inoperative
F22 Fan oven (ring) heater element inoperative
F23 Pyrolysis heating fault
F24 Heating relay contact
F25 Desired temperature fault
F26 Vacant
F27 Vacant
F28 Vacant
F29 Vacant
F30 Door and door contact – Different signals
F31 Door open with defective door lock
F32 Door lock does not close
F33 Door lock does not open
F34 Locking not possible
F35 Unlocking not possible
F36 Vacant
F37 Vacant
F38 Vacant
F39 Vacant
F40 Electronic unit fault
F41 Faulty EEPROM / incorrect data
F42 No mains frequency recognition
F43 Model type not programmed
F44 I²C bus defective
F45 Flash RAM defective / Incorrect data
F46 LCD connection defective
F47 BAE/ SLT interface defective
F48 Vacant
F49 Vacant
F50 Drive
F51 Level switch, pressure sensor
F52 Heating pressure switch has reset during heating
F53 Speed sensor fault
F54 Spit short-circuited
F55 Overriding time control exceeded
F56 Final spin speed < 400 rpm
F57 Cooling fan fault
F58 Hot air fan fault
F59 Water container fault
F60 Excessive temperature
F61 12 V not present
F62 Undefined fault
F63 Water path control unit fault
F64 Path sensor defective
F65 Drum lighting cap missing
F66 Air path leakage
F67 Circulation pump speed too low
F68 Circulation pump operates after switch-off
F69 Plinth float switch
F70 Vacant
F71 Magazine drive defective
F72 Feed drive defective
F73 Percolator unit drive defective
F74 Valve drive defective
F75 Remove capsule from percolator unit
F76 Capsule jammed during pressing
F77 Valve resetting defective
F78 Vacant
F79 Vacant
F80 Heater unit – Water inactive
F81 Heater unit – Steam inactive
F82 Heater unit – Water – Excessive temperature
F83 Heater unit – Steam – Excessive temperature
F84 Water path control unit position at intake
F85 Water path control unit permanent signal change
F86 Lid contact – Salt
F87 Sensor softener
F88 Turbidity sensor
F89 O2-Sensofault
F90 O2-Systemfault
F91 Load recognition not active
F92 Volume flow counter faulty

[Beever]

Re: BOSCH WFL2260UK/01 w/m

How did you get on with the bosch maxx WFL (active light flashing after replacing the door seal?)

Regards

Ian B
:martin:

[Beever]

Re: BOSCH LOGIXX DISHWASHER SGS66A02GB/17 STRANGE FAULT

The replacment part no is now 497570 £16.74

Regards

Ian B

🙄

[Beever]

Re: Bosch KIV3235GB/42

Appliance may have a gas leak, that is why the rear wall has blistered away from the evap. system could now be short of gas, thats why it will not cool lower than 10deg. Appliance is prob a write off.

[Author]

Posts