colly

Forum Replies Created

Viewing 15 posts - 16 through 30 (of 83 total)
1 2 3 4 5 6
  • Author
    Posts
  • February 6, 2012 at 8:45 pm in reply to: Bosch wfo2864gb wiring diagram #368363
    colly
    Participant

    Re: Bosch wfo2864gb wiring diagram

    Cheers man passed info on

    January 18, 2012 at 9:11 pm in reply to: John Lewis JLWM 1405 washing machine #366518
    colly
    Participant

    Re: John Lewis JLWM 1405 washing machine

    Hi all

    Managed to sort this one out

    E58/59 error code

    I found a broken wire at motor plug (wiring harness )


    😀 😀 😀
    Thanks for your help

    Colin

    January 4, 2012 at 10:21 am in reply to: John Lewis JLWM 1405 washing machine #366517
    colly
    Participant

    Re: John Lewis JLWM 1405 washing machine

    Colinconeill@hotmail.com

    Have tried as in other zanussi Electrolux procedures but no working on this model

    I can get her jl dryer into test mode no trouble at all .

    That is not faulty though . Lol

    November 28, 2011 at 8:04 pm in reply to: Beko WME8227B #362205
    colly
    Participant

    Re: Beko WME8227B

    Hi all

    Been to a Beko WME8227b washing machine almost fully working but has an f2showing at bottom of display.

    Put machine on 39 minute wash and starts to chuck the water out at 26 mins on the display then stops with some water in the bottom of the drum.

    Machine drains fast , fills, rotates, spins, and heat’s,

    Any ideas or error code’s for this range ?

    Kind regards

    Colin

    October 31, 2011 at 10:49 pm in reply to: LG Dryer RC8003R Error BE #361596
    colly
    Participant

    Re: LG Dryer RC8003R Error BE

    Hi

    Have a dryer with same error code have you been able to repair be fault code?

    Regards

    Colly

    September 7, 2011 at 6:58 pm in reply to: Electrolux T4530 9872310025 #358486
    colly
    Participant

    Re: Electrolux T4530 9872310025

    Type your model number into google also e14 fault

    There seems to be info there on it

    colly

    August 12, 2011 at 7:08 am in reply to: Zanussi fle1416 no lights/ start #356574
    colly
    Participant

    Re: Zanussi fle1416 no lights/ start

    will give it a go

    August 2, 2011 at 5:27 am in reply to: Zanussi fle1416 no lights/ start #356571
    colly
    Participant

    Re: Zanussi fle1416 no lights/ start

    Hi gandh1
    Thank you for your reply
    Bearings are good !!
    I did have a board of another zanuss,not correct one, but same style and working.
    It came of a bearing failure machine also.

    Put it on machine and the same thing seemed to be happening other than when machine first switched on lights on fascia did light up for a few secs it then reverted to original fault.
    colly

    June 25, 2011 at 9:59 pm in reply to: AEG OVEN NO CLOCK DISPLAY DS701-4-A #354082
    colly
    Participant

    Re: AEG OVEN NO CLOCK DISPLAY DS701-4-A

    Hi dave
    It is a transformer on pcb

    i will check it for continuity

    Cheers

    Colin

    June 23, 2011 at 9:47 pm in reply to: AEG OVEN NO CLOCK DISPLAY DS701-4-A #354080
    colly
    Participant

    Re: AEG OVEN NO CLOCK DISPLAY DS701-4-A

    Hi dave
    cannot see any wrong with power module caps dry joints etc

    I have not inspected clock pcb

    As for top oven / grill you can remove all wires from power board and these will still operate fine.

    Power board is just for the main oven.

    Clock is an obsolete part even though oven is just over 5 years old .

    No one seems to have board in stock not even disrti

    Cheers

    Colin

    June 23, 2011 at 9:41 pm in reply to: AEG OVEN NO CLOCK DISPLAY DS701-4-A #354079
    colly
    Participant

    Re: AEG OVEN NO CLOCK DISPLAY DS701-4-A

    Martin wrote:What’s the PNC number?

    944171273

    June 17, 2011 at 9:36 am in reply to: Aeg fault E5H #353291
    colly
    Participant

    Re: Aeg fault E5H

    Well you know I may just have to be a brave man

    If I can find a used part .

    Colly

    June 15, 2011 at 8:34 pm in reply to: Aeg fault E5H #353289
    colly
    Participant

    Re: Aeg fault E5H

    Hi martin

    Did you attempt to repair the machine ?

    Colly

    June 15, 2011 at 8:04 am in reply to: Hotpoint oven error code 08 #353588
    colly
    Participant

    Re: Hotpoint oven error code 08

    Hi guys

    Been and checked oven out this morning .

    I have found cooling fan was not running (just humming)

    A bit of oil in the bearing end cap has sorted it .

    Cheers

    Colly 😀

    June 14, 2011 at 9:39 pm in reply to: Hotpoint oven error code 08 #353587
    colly
    Participant

    Re: Hotpoint oven error code 08

    Hi according to the customer it is

    on qualtex comes up ariston parts i think’s

    colly

  • Author
    Posts
Viewing 15 posts - 16 through 30 (of 83 total)
1 2 3 4 5 6