colly

Forum Replies Created

Viewing 8 posts - 76 through 83 (of 83 total)
1 2 3 4 5 6
  • Author
    Posts
  • April 20, 2011 at 9:04 pm in reply to: Zanussi E40 fault #349494
    colly
    Participant

    Re: Zanussi E40 fault

    Hi paul
    Got back to that zanussi today and did find a blown triac where you suggested.
    Have sent board away for repair/test (£10} so i think it’s going to work ok.
    Cheers mate for your sound advice.
    Colin

    April 20, 2011 at 5:36 am in reply to: Bosch wvf2047GB/02 #349698
    colly
    Participant

    Re: Bosch wvf2047GB/02

    Hi
    Is the water draining after wash properly?

    A blocked filter can cause machine to carry straight on after finishing
    Current selected cycle;

    colin 😉

    April 18, 2011 at 7:10 pm in reply to: Zanussi E40 fault #349493
    colly
    Participant

    Re: Zanussi E40 fault

    HI martin
    Removed pcb the other day no evidence of a blast mark
    Cheers for your post though
    Colin

    April 17, 2011 at 7:13 pm in reply to: Zanussi E40 fault #349491
    colly
    Participant

    Re: Zanussi E40 fault

    Hi paul
    I will go back to check for your suggestion.
    Cheers
    Colin

    April 17, 2011 at 6:22 am in reply to: Hotpoint indesit range washing machines no start door not #349512
    colly
    Participant

    Re: Hotpoint indesit range washing machines no start door n

    Hi
    Thank you for your input i will bear this in mind for future .
    I know the hotpoint lads do not do any of the above with the plug and they change the motor and machine does then work ok .
    i wonder how that is ?
    Perhaps the new motor has thicker terminals in the plug socket .
    I have squeezed the connections and found it to be a sound repair .
    But i will think about what you have said for next one.

    October 27, 2010 at 7:06 pm in reply to: SIMPLE PCB REPAIR TIPS #309695
    colly
    Participant

    Re: SIMPLE PCB REPAIR TIPS

    Hi
    I have come across the flashing lights fault on hotpoint’s twice in the last couple of months.
    Luckily last time i had the correct used module to fit .
    However on this occasion i had read your post on here, i changed the capacitor on the board , and was happy to find it worked.
    Thanks for your post !
    colin

    October 27, 2010 at 6:54 pm in reply to: SIMPLE PCB REPAIR TIPS #309694
    colly
    Participant

    Re: SIMPLE PCB REPAIR TIPS

    iadom wrote:HOTPOINT/INDESIT. Flashing all display lights.

    Excellent advice from forum member Lasty.

    In most cases the largest of the three adjacent capacitors on the main board rated 680u – 10v …. has failed.

    The top of the capacitor appears domed.

    Replacement costs all of 17 pence.

    CAPACITOR


    Jim..

    July 22, 2007 at 5:16 pm in reply to: Bosch Sensor Dryer WTL6103GB/01 #221331
    colly
    Participant

    Re: Bosch Sensor Dryer WTL6103GB/01

    Hi my name is colin
    just been called out to a family/friends dryer with no heat also .
    removed the back and hoped the stat would have just tripped but in this case of course not.
    tested the thermistor stat above element and get a reading element reads ok also found exhaust thermistor in front of dryer but not sure what these thermistors should read.
    any more idears ?
    regards
    colin

  • Author
    Posts
Viewing 8 posts - 76 through 83 (of 83 total)
1 2 3 4 5 6