dave-m

Forum Replies Created

Viewing 15 posts - 181 through 195 (of 199 total)
1 2 3 … 12 13 14
  • Author
    Posts
  • February 21, 2011 at 2:18 pm in reply to: Whirlpool AWO/D5526 #345270
    dave-m
    Participant

    Re: Whirlpool AWO/D5526

    thanks for that whiskey-six, doubt she’ll spring for one of those,

    Cheers

    DM

    February 21, 2011 at 2:02 pm in reply to: Whirlpool AWO/D5526 #345268
    dave-m
    Participant

    Re: Whirlpool AWO/D5526

    Just got this back from her, 859296815005.
    Bearings gone apparently.

    February 21, 2011 at 11:04 am in reply to: AEG INT D/W F88070VI fault code i60 #345236
    dave-m
    Participant

    Re: AEG INT D/W F88070VI fault code i60

    i60 is heating time-out /overheating. Element/thermostat/ntc.

    February 14, 2011 at 6:53 pm in reply to: Uploading Pics #344585
    dave-m
    Participant

    Re: Uploading Pics

    I’ll try those guys, thanks for the help.

    DM

    February 14, 2011 at 6:52 pm in reply to: Washer/Dryers #344605
    dave-m
    Participant

    Re: Washer/Dryers

    No problem, I’ll be back if I’ve specific problems.

    Cheers

    DM

    January 23, 2011 at 9:04 pm in reply to: zwf12070s #342119
    dave-m
    Participant

    Re: zwf12070s

    cheers Paul

    D

    January 23, 2011 at 10:07 am in reply to: zwf12070s #342117
    dave-m
    Participant

    Re: zwf12070s

    That really will help Martin.

    Much appreciated.


    d

    January 21, 2011 at 8:57 pm in reply to: electrolux d/w ESL66010 #341877
    dave-m
    Participant

    Re: electrolux d/w ESL66010

    I’m going to see it next week and i’ll check the element and get the pnc if its good.

    Thanks a lot chris.

    d

    January 21, 2011 at 10:29 am in reply to: electrolux d/w ESL66010 #341875
    dave-m
    Participant

    Re: electrolux d/w ESL66010

    Thanks a mil chris,

    Do you mean heater OR pcb faulty.
    If its the pcb is it worth changing, are they expensive?
    I can’t get a price in the UKW shop here.

    Thanks again

    d

    January 6, 2011 at 9:56 pm in reply to: ISE10 1607w in the house! #338552
    dave-m
    Participant

    Re: ISE10 1607w in the house!

    Does anyone know if you can buy these machines in Ireland?

    Regards

    dave

    November 9, 2010 at 5:23 pm in reply to: Beko WMA510W #335296
    dave-m
    Participant

    Re: Beko WMA510W

    Lawrence,

    Sounds like its not spinning all the time?
    I’d check the wiring to the motor and the magnet in the tacho. Those magnets are troublesome and any damage to them can make it spin intermittently.

    dave

    November 6, 2010 at 7:55 pm in reply to: wf 560 #335171
    dave-m
    Participant

    Re: wf 560

    Will do.

    Cheers

    dave

    November 2, 2010 at 6:22 pm in reply to: beko wma520 #334478
    dave-m
    Participant

    Re: beko wma520

    Well, Glued the magnet and left it overnight to set and popped it back in the machine and hey presto, it worked. But after putting it on to spin three times to make sure, it cut out again, magnet cracked again in a new place so it must have been more damaged than i thought on first inspection.
    However, I rang a guy I know from Beko and he has a motor that I can have for thirty bucks.
    So I’ll have it up and running tmro without the worry of a call back.
    Everyday’s a school day.
    Ta shaun and everyone else for the help.

    Dave

    October 30, 2010 at 10:46 am in reply to: beko wma520 #334476
    dave-m
    Participant

    Re: beko wma520

    Hey Shaun,

    Cheers for the tip about araldite rapid steel. I was just going to use bog standard araldite, as I’d not heard of rapid steel, and I wasn’t as hopeful as I might have been. But that stuff sounds like a better proposition altogether. I’m off down to Hal@#*ds now to pick some up.
    Won’t get my tacho til next week but I’ll keep you in the loop.

    Cheers

    Dave

    October 29, 2010 at 6:50 pm in reply to: beko wma520 #334474
    dave-m
    Participant

    Re: beko wma520

    Just looked at that machine again, The tacho coil is goosed! So I’ll have to wait to get one of them. The only problem is that the magnet is also cracked and it doesn’t look like a replacable part as its bonded onto a brass ring. Could I just glue the magnet back or will it mess up the new coil?

    d

  • Author
    Posts
Viewing 15 posts - 181 through 195 (of 199 total)
1 2 3 … 12 13 14