Forum Replies Created
-
Posts
-
Re: Bearing Replacement -Zanussi FLA 1001W
It’s a complete rear tub replacement I’m afraid (which comes with the bearings).
I’ll need the product code to identify though as there are 2 version, this will be on the rating plate inside the door and begin 9147……….
Dave.
Re: Ariston Margherita 2000 – I also have a problem!
Kipster, PCB is part number C00093158 at £62.20 plus VAT and carriage, delivery time 3-5 days.
Jim c, details as follows:
Heater C00080765 at £16.80
Thermistor C00080767 at £4.35
Thermal fuse C00080775 at £9.45
All plus VAT and carriage.An email to spares@ukwhitegoods.co.uk please if any of the above are required 🙂
Dave.
Re: Diplomat ADP8322
It means it’s not draining. From the description of the sound an object may have got in to the pump and jammed it or possibly the pump has failed.
Power off if investigating :zap: or if you’re unsure, check the repairs@ link below 🙂
Dave.
Re: nardi cooker
Part number 090148009901R at £16.18 inc VAT and carriage 🙂
If you’d like one, an email to spares@ukwhitegoods.co.uk please (it may be slow on delivery though knowing Nardi)
Dave.
Re: AEG LAVAMAT – CHANGED BRUSHES BUT STILL C9 CODE
jonathantong wrote:Hopefully this is enough to work out what I need!
It does thanks, if you order these Hotpoint ones:
http://www.ukwhitegoods.co.uk/modules.p … cts_id=499
They’re exactly the same (I just opened a pack to check) 😀
Dave.
Re: AEG LAVAMAT – CHANGED BRUSHES BUT STILL C9 CODE
Well, it appears AEG (Zanussi) have changed the spec on the brush on certain motors and the brushes in the link are too narrow for some FHP motors.
Can you post the dimensions of the remainder of the brush please (apart from the length obviously ;)) and I’ll check the correct ones for you 🙂
Dave.
Re: How do you drain off a flooded WMA?
walnut wrote:pump like buggery
😯
Now where’s my Carry On phrase book ? 😆
Dave.
Re: Universal drain hose extension kits
whitevanman wrote:I use 4 inch length of 22mm copper pipe , 2 jubilee clips and some debor.
That’s the solution I have used also when required bit I guess a lot of the guys won’t have 22mm copper pipe on the van unless they do gas work, but it would be my preference over the “universal” types.
There’s still quite a few appliances that don’t have rubber ends on the waste hose as well.
Andy, that part is a total rip off IMO at that price from sparesRus 🙁
Dave.
Re: Universal drain hose extension kits
Have you got a part number or link to anything specific Andy ?
Dave.
Re: DCS 14W Zanussi Tabletop Dishwasher Top/Front Panel
Part number 1509471007 at £28.29 inc VAT and carriage.
I can easily obtain this for you, an email to spares@ukwhitegoods.co.uk please if required 🙂
Dave.
Re: Smeg DWI 67.1 pump impellor fitting!
db2boy wrote:There is honestly no thread in the moulding, it is 100{e5d1b7155a01ef1f3b9c9968eaba33524ee81600d00d4be2b4d93ac2e58cec2d} smooth.
😯
I would say almost without doubt that it should be. It is possible that it wasn’t threaded correctly at the factory but very rare.
Let me know please 🙂
Dave.
Re: Smeg DWF 44 SS.1 motor
andy_b wrote:I have seen one on the internet for £150 😯
That’s correct I’m afraid, the price is £130.94 inc VAT (less carriage which would be quite high to be shipped to France from the UK due to it’s weight).
I would rule out the motor start capacitor first though (or ask the engineer to) 😉
Dave.
