Forum Replies Created
-
AuthorPosts
-
Dave_Conway
ParticipantRe: rear bearing shaft/spindle, for a CREDA 37449001SL
:wave:
Dave_Conway
ParticipantRe: servis soap box
Or was that the wrong part number as 720109800 is the lid ?
If 728002200 is incorrect then you need 728002300 (picture of both on Connect’s site if you have access)
Dave.
Dave_Conway
ParticipantRe: servis soap box
I gave the correct part number on this thread:
http://www.ukwhitegoods.co.uk/modules.p … ght=#74315
It’s 728002200 🙂
Dave.
March 17, 2006 at 11:47 am in reply to: BOSCH DISHWASHER sgs56a72gb/17 STUCK ON 1 MINUITE ON DISPLAY #169763Dave_Conway
ParticipantRe: BOSCH DISHWASHER sgs56a72gb/17 STUCK ON 1 MINUITE ON DIS
Twice ? 😆
No problem.
Dave.
Dave_Conway
ParticipantRe: rear bearing shaft/spindle, for a CREDA 37449001SL
Drum shaft repair kit part number 1701662 but it’s for the later drums, as Iadom says, you may have to “modify” to fit 😉
Dave.
Dave_Conway
ParticipantRe: Cannon Stratford gas cooker
Part number 6604026 🙂
Dave.
Dave_Conway
ParticipantRe: Diplomat ceramic hob
APL1304 by any chance ? 😉
Part number 11540550 at £15.99 ex VAT each list.
Dave.
Dave_Conway
ParticipantRe: Diplomat integrated d/w
Part number 993736190 £20.36 list from MFI on 08457 959722 (this will apply to the other two enquiries I’m about to answer ;)) or as it’s a Smeg other wholesalers may have it.
Dave.
PS, it’s an ADP8234 🙂
Dave_Conway
ParticipantRe: Hotpoint dishwasher problem dwt-10!!!!!!!!!!!!!!!!
It’s detecting a “no drain” error.
Check for outlet blockages where the waste hose connects etc.
Apart from that, it could be one of a few things internally causing it, blockages, pump failure, level sensor failure etc.
Check the repairs@ link below if you need an engineer or power off if you decide to go in yourself :zap:
Dave.
Dave_Conway
ParticipantRe: One to keep an eye on.
His website:
He repairs cookers so I had no option really 🙂
Dave.
Dave_Conway
ParticipantRe: Hoover HCA450FK Freezer Not Cold Enough
clarkparf wrote:Should I try defrosting for 24 hrs in case of ice build up somewhere
It’s certainly worth a try as nearly all frost free units will become overiced in time.
If that doesn’t solve it the noise would indicate a possible fan motor failure, probably the freezer one by the fault description.
Se what happens after the defrost and let us know 🙂
Dave.
Dave_Conway
ParticipantMarch 16, 2006 at 6:27 pm in reply to: BOSCH DISHWASHER sgs56a72gb/17 STUCK ON 1 MINUITE ON DISPLAY #169760Dave_Conway
ParticipantRe: BOSCH DISHWASHER sgs56a72gb/17 STUCK ON 1 MINUITE ON DIS
Looking at previous posts it’s either a partial blockage or the turbidity sensor covered in gunge, these (some public) posts should help:
http://www.ukwhitegoods.co.uk/modules.p … ic&t=10449
http://www.ukwhitegoods.co.uk/modules.p … pic&t=8327
http://www.ukwhitegoods.co.uk/modules.p … ic&t=12293
Dave.
Dave_Conway
ParticipantRe: ariston A1124uk
It sounds like the PCB in that case 🙁
For a definite diagnosis, check the repairs@ link below for an engineer 🙂
Dave.
Dave_Conway
ParticipantRe: Unknown D/W
If the model has /1 on the end then yes, it’s different. That would have a large Askol type motor in it but they don’t leak (very often) so I think you should be OK 😀
Dave.
-
AuthorPosts
