[Dave_Conway]

Re: Samsung RS21 WCSV

DA41-00185J according to SEME at just under £75 ex VAT 😯

That’s the only PCB listed for that model so I guess it’s the main one.

Dave.

[Dave_Conway]

Re: Bosch KGU3201

It does sound like the compressor to be honest but only an engineer’s visit would verify for sure, this would also be the case for replacement as specialist equipment is required to replace one which includes a system refrigerant re-charge etc.

Dave.

[Dave_Conway]

Re: ZANUSSI F/F ADVICED NEEDED

There seems to have been a few enquiries on here about unexplained warning sounds from these models 😕

These are electronically controlled and all components need checking to eliminate the likely failure, it’s engineer time to be honest.

Check the repairs@ link below 🙂

Dave.

[Dave_Conway]

Re: Where can I get an ignition switch? Cannon Canterbury mk

Part number 6604765 at £19.06 inc VAT plus carriage in that case 🙂

An email to spares@ukwhitegoods.co.uk please if required

Dave.

[Dave_Conway]

Re: hotpoint rla80 fridge

As it’s a tall larder I doubt a VT9 will have a long enough capillary to be honest.

Hotpoint list two stats for this model:

Danfoss – 2603479
Ranco – 2603145

No indication of whether they interchange or not though 🙁

Dave.

[Dave_Conway]

Re: skinny jubilee clips

cornwell40 wrote:Would they fit in between the Whirlpool heater hose ridges?

Probably, but then so would these on this thread 😀

http://www.ukwhitegoods.co.uk/modules.p … ic&t=12180

Dave.

[Dave_Conway]

Re: Siemens Hob simmerstat

Without seeing them it’s hard to tell, the part numbers don’t show up any alternatives.

Dave.

[Dave_Conway]

Re: CDA DOUBLE OVEN MODEL CD 900/906

If it’s just been fitted (new ?) then the neon may have fallen out of it’s holder or a wire may be loose.

Assuming it’s new then I would contact CDA and ask that they send an engineer to check it out, if a lead has come loose it could cause more damage 😉

Dave.

[Dave_Conway]

Re: Manor House WKD 4BL d/w

It is Spanish, it’s a Fagor 🙂

Timer part number V71D000L1 about £40 (special order) from Masterpart and/or Connect.

Dave.

[Dave_Conway]

Re: Where can I get an ignition switch? Cannon Canterbury mk

It shouldn’t be a problem but we will need the model number please 🙂

Dave.

[Dave_Conway]

Re: Hotpoint BFI62 error codes?

Fill valve, pressure switch, blockages , PCB etc, any number of things to be honest 😉

Dave.

[Dave_Conway]

Re: Hotpoint BFI62 error codes?

It means it’s not filling basically.

I would check your water supply first of all (kinked hose etc), apart from that a number of things may cause this.

Power off please if you go in yourself :zap: or check the repairs@ link below for an engineer 🙂

Dave.

[Dave_Conway]

Re: Zanussi fridge doesn’t cool very well

richiebman wrote:I have a Zanussi fridge freezer (model number not at hand)

We will need it to be honest to offer accurate advice 😉

richiebman wrote:Also can anyone suggest a good/reliable/not extortionate fridge repair company?

Check the repairs@ link below, Sheffield has cover for refrigeration 🙂

Dave.

[Dave_Conway]

Re: smeg fan oven heating unreliably

Yes, I’d go along with Bryan on that, selector or thermostat normally.

You should find an engineer by following the repairs@ link below 🙂

Dave.

[Dave_Conway]

Re: Firenzi DW 930/1 beeping/flashing lights

Yes, that’s about right.

I would have it repaired to be honest, the replacement motors for these have been modified and are far more reliable than the original.

Dave.

[Author]

Posts