Dave_Conway

Forum Replies Created

Viewing 15 posts - 3,571 through 3,585 (of 12,426 total)
  • Author
    Posts
  • in reply to: whirlpool frost free motor #166326
    Dave_Conway
    Participant

    Re: whirlpool frost free motor

    You got a photo Simon (the picture on SIOS is dreadfull 🙁 ) ?

    Dave.

    in reply to: Hotpoint Freezer FZA80N , no go #166325
    Dave_Conway
    Participant

    Re: Hotpoint Freezer FZA80N , no go

    It may be worth checking the thermal cut outs behind the rear wall, apart from that it can’t really be much else than the PCB.

    Dave.

    in reply to: Zanussi zds699ex 911896024 #166323
    Dave_Conway
    Participant

    Re: Zanussi zds699ex 911896024

    Part number 1524369004 at £76.61 ex VAT (list).

    Electrolux themselves have stock, 01325 302464 🙂

    Dave.

    in reply to: Rangemaster 110 Dual Fuel #164033
    Dave_Conway
    Participant

    Re: Rangemaster 110 Dual Fuel

    Part number A094693 at £19.95 plus carriage.

    An email to spares@ukwhitegoods.co.uk please if you’d like one 🙂

    I did reply to your email some days ago regarding this, perhaps it got lost in the ether 😕

    Dave.

    in reply to: Zanussi FM5230 Oven Door Hinge Replacement #166271
    Dave_Conway
    Participant

    Re: Zanussi FM5230 Oven Door Hinge Replacement

    Check here on how to remove the door first of all, it should be fairly straightforward after that 😉 :

    http://www.ukwhitegoods.co.uk/modules.p … pic&t=3771

    Incidently, the hinges are £21.26 for the pair and you may also require the hinge supports at £5.30 each as these also wear (both inc VAT, ex carriage).

    spares@ukwhitegoods.co.uk if you need them 🙂

    Dave.

    in reply to: BUILT IN D/WSH CDA CW494 #166253
    Dave_Conway
    Participant

    Re: BUILT IN D/WSH CDA CW494

    :wave:

    Definitely a Whirlpool according to CDA’s tech disk 😉

    Dave.

    in reply to: Belling fan oven – XOU164WH/2 #166266
    Dave_Conway
    Participant

    Re: Belling fan oven – XOU164WH/2

    082618154 is the part number, I doubt there will be an alternative though 🙁

    Dave.

    in reply to: Hoover dishwasher DT999 #166276
    Dave_Conway
    Participant

    Re: Hoover dishwasher DT999

    It’s on the outside, atached to the upper spray arm supply pipe by the looks of it, I have this snippet:

    Hoover wrote:The new system is based on the use of a new heating assembly, now located externally to the washing chamber, immediately below the cabinet’s left outer side panel.

    HTH

    Dave.

    in reply to: poor spin full loads only #166247
    Dave_Conway
    Participant

    Re: poor spin full loads only

    The “61 = not reaching temp” suggests a heater fault perhaps ?

    It may be interfering with the PCB/Spin control.

    Dave.

    in reply to: Candy Fridge Freezer – Advice pls #166191
    Dave_Conway
    Participant

    Re: Candy Fridge Freezer – Advice pls

    Odd one 😕

    Either someone has tampered with the wiring or it has an unusual elelctrical fault.

    Engineer time to be honest, check the repairs@ link below 🙂

    Dave.

    in reply to: samsung washer pump #166267
    Dave_Conway
    Participant

    Re: samsung washer pump

    Available from Connect for about £40, their part number 5031687720542

    Dave.

    in reply to: BUILT IN D/WSH CDA CW494 #166251
    Dave_Conway
    Participant

    Re: BUILT IN D/WSH CDA CW494

    It’s a Whirlpool, codes in the “known error codes” thread 🙂

    Dave.

    in reply to: Homark Oven – Door Seal & Oven Stat #166249
    Dave_Conway
    Participant

    Re: Homark Oven – Door Seal & Oven Stat

    Door Seal – 79X8948 – £31.05 😯
    Thermostat – 76X3759 – £27.58

    Both inc VAT, plus carriage. Delivery within a few days of order.

    If you’d like them, an email to spares@ukwhitegoods.co.uk please 🙂

    Dave.

    in reply to: Servis M491W #166226
    Dave_Conway
    Participant

    Re: Servis M491W

    Check the rotation of the spray arm by facing it in one direction while it’s washing then open the door to see if it’s moved.

    That sounds like where the problem lies.

    Dave.

    in reply to: ERROR CODES FOR NEW HOTPOINT NEEDED #166229
    Dave_Conway
    Participant

    Re: ERROR CODES FOR NEW HOTPOINT NEEDED

    In the known error codes at the top of this forum Razor 😉

    Dave.

Viewing 15 posts - 3,571 through 3,585 (of 12,426 total)