Forum Replies Created
-
Posts
-
Re: Smeg FC40RX fridge/freezer
It’s more likely that it is the other way round Carl.
The fridge compressor would normally have a tray on top of it to collect the defrost water.
Neither compressor should run hot, the one that is warm is working correcty, the hot one is not and there is a problem either with the compressor itself or some other system failure.
I would suggest you call an engineer to check for you, you could try here in repairs@ and the directories for one.
Dave.
Re: Candy CPCA291FFK fridge freezing milk
Change them both I would Simon.
PCB 41007946
Thermistor 49003477There’s a tech bulletin on both of those part numbers as well which I think comes with the PCB.
Dave.
Re: Zanussi ZX77 Fridge Freezer
Possibly, if it does please come back and check here as you’ll need an engineer to rectify the underlying cause.
Dave.
Re: Faulty 8702 flooded our downstairs flat
Anonymous wrote:As you say, I feel it has to be an inlet valve fault.
I didn’t, I said it’s more likely to be the waste hose problem, which won’t effect the function of the appliance at all, only fill it with water when not in use. Although if it is clean, then it is likely to be the valve. Wait and see what the engineer discovers on Friday.
Easy way to find out is turn the taps off that supply it and see what happens (I would suggest this anyway, just in case).
As far as compensation etc goes, I can’t advise on this I’m afraid, that is best discussed with MFI and the installers.
Dave.
Re: Diplomat oven
The fan element has failed I expect.
If you can supply the model number we will try to help a bit further for you Malcolm 😀
Dave.
Re: Candy Alise 105 Drum Bearing Maintenance…
Evren, please take my initial advice 😉
Lubricating the bearings even if you could access them wouldn’t make any difference at all.
Dave.
Re: Faulty 8702 flooded our downstairs flat
May I ask who installed the appliance ?
The reason I ask is that it may well be that the drain hose is not positioned correctly and if it’s connected to the sink trap then it may well back drain in to the machine from the sink.
If that is the case then it’s the installers that are at fault and not the manufacturer. It’s highly unlikely (but possible) that a new inlet valve would be letting water pass.
Those are really the only two possibilities.
Dave.
Re: tecnik
I can’t find anything on this model anywhere 🙁
Have a look at their website for contacts:
http://www.tecnik.net/home.htm
Dave.
Re: Grill pans/handles
The lowest price I can find on grill pans complete is £6.50 from Kitchen Economy their handles are the cheapest as well.
Obviously that’s in singles but it may be worth a call, details:
Phone (029) 20451222
Email enquiries@kitchen-economy.co.uk
Dave.
Re: Zanussi WDJ1285 drum bearing
It varies a bit Alexis but you would look at paying between £100 and £150 as a guide depending on whether the drum shaft was damaged or not.
Parts can be obtained via the shop@
Bearing kit is here:
http://shop.ukwhitegoods.co.uk/Washing+ … l+Kit.html
And the tub seal here:
http://shop.ukwhitegoods.co.uk/Washing+ … +Seal.html
If you need the drum shaft/spider come back to me 😉
Dave.
Re: Candy Alise 105 Drum Bearing Maintenance…
You can’t lubricate the bearings without removing the whole drum I’m afraid.
If they are getting noisy, the only solution is to replace them, and on these models it is very time comsuming and (in my opinion) not an economically viable job to do.
The actual parts wouldn’t be expensive, around £20 for the bearing kit but the labour involved makes it a costly job.
Dave.
Re: Door Seal for Diplomat 620 multifunction oven
We’ll need the full model please, AHY36 will have two more numbers after that.
Check around the door frame/oven cavity 😀
Dave.
