Forum Replies Created
-
Posts
-
Re: ISE 1606W & CD60W
a very succinct reply Ken.
I have an Asko dishwasher which is 24 years old! used virtually every day.
We were an Asea sales & service centre which was taken over by Asko.
I get fed up of hearing the term `over engineered` applied to manufacturers such as Asko, I personally hope they keep to their values. I had the pleasure of visiting the factory in the late 80`s & can confirm everything you have said about their pride in their product.I will be happy to carry on selling the new Asko machines whoever owns them!!!
dave
Re: SMEG FME 24X Microwave
72X0267 changes part number to 76X7995, Ive only ever seen the type with the mains input connections at the bottom of the board.
thanks for the heads up eastlmarkDave
Re: When was this Servis made??
Is it the dispenser lid you are looking for?? if so:
I dont think they are interchangeable the part number ive found is:
330101900
connect are showing it in stock at a tenner cheaper than the later version.
The later one starts from 19/09/07. week 23 is 1st week of June.
So you should be able to get hold of the correct one.
daveRe: When was this Servis made??
usually first 4 digits yr next 2 digits week number.
so week 23 of 2007?????good luck
Re: SMEG FME 24X Microwave
Masterpart details:
4 Grainger Road
Southend On Sea SS2 5BZ
01702 310031
http://www.masterpart.comI think Masterpart sponsor the trade spares forum on UKW?
Cheers
Dave
Re: SMEG FME 24X Microwave
I think this may be the same microwave as I have worked on. It is available from loads of manufacturers (electrolux, AEG to name 2).
Has the door lock module blown or overheated.Usually the area around the microswtch legs is Burnt away. dry solder joint but like the worst you have ever seen?
If it is then I have changed quite a few for this reason.
Masterpart (if you deal with them) list it as part number 76X7995 for about £30 + vat I think.Good luck
Dave
Re: ISE10 Fault F1
coincidence!!! just had call through this morning ise10 fault f1.
not going till thursday so will check what you have said bazza500.Re: whirlpool aquasteam w/m awod/as128 f06
thanks for the reply, John.
I put it on a wash & after 12 mins the motor speed ramped then F06.
Checked the tacho coil it was open circuit…reset the machine put it on a spin did this ok checked the coil was showing correct resistance.
Found a scrap motor of same make transferred tacho coil…so far seems to have cured the fault!!!Anyone else had intermittant tacho coils?? I`ve seen fill valves do the same thing but so far not a tacho coil.
Cheers
Dave
Re: Miele W842 tacho/carbon brush holder
many thanks clayside, module indeed I always thought that was a PCB?
I`d have never identified by description would I.thanks again
Re: whirlpool awm9000
without the service number (starts 857….)
clamp for gasket to tub is listed as 481240118657 for an AWM9000
connect show it in stock.cheers
Re: smeg wdi12c1 no spin
checked module cant see any dry joints so I guess bad news for customer.
many thanks lawrence, the way of it nowadays.
Re: Miele dishwasher G997
hi clayside
thanks for your reply but I think from your description of parts the only part number you havent given me is for the pipe on the back wall?
I think it is this pipe that we need.
sorry for my vague descriptionsta
Re: Miele dishwasher G997
hi sorry for delay,
the part required sits inside d/w at back the tube on the top basket with the top spray arm on connects to it when u slide the basket back.hope that is enough to identify it.
many thanks
Re: AEG D4101-4-a Oven Thermostat
before ordering thermostat did u check whether there was a guard
over the fan on the backplate of the oven?
if there is remove it & check temp again.
I`ve seen a few where this gets covered in grease and causes the stat to
cut out before the oven has reached proper temp.
